SoundCraft 1601S manual Making Adjustments and Fitting Spares, Setting The Pre-trim Pads

Page 14

MAKING ADJUSTMENTS AND FITTING SPARES

CAUTION: THE FOLLOWING SECTION IS FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE TOP FASCIA TO PERFORM ANY SERVICING OR OTHER TASKS, UNLESS YOU ARE QUALIFIED TO DO SO.

BEFORE REMOVING THE TOP FASCIA ENSURE THE UNIT IS

DISCONNECTED FROM THE MAINS SUPPLY.

ONLY REMOVE THE ALLEN SCREWS INDICATED ON THE DIAGRAM OPPOSITE.

WARNING: DO NOT OVER-TIGHTEN THE SCREWS AFTERWARDS.

It is necessary to remove the top panel fascia in order to carry out one or more of the following tasks:

Setting the pre-trim pads on channels 1 & 2 during installation.

Changing the orientation of the Phono/Line switches.

Replacing any of the four linear faders.

Removing the Sampler section

To remove the top panel fascia proceed as follows:

Pull off all the fader and pot knobs.

Undo the 6 retaining Allen screws using a 2mm Allen key. These are located down the left and right hand edges of the fascia. The fascia can now be lifted clear of the subframe underneath. Take care not to bend the panel.

The diagram opposite shows a view of the mixer (1601S) without the top fascia fitted.

Setting The Pre-trim Pads

There are 2 pads on each of the 2 input channels. The -20dB pads are on either side of the FX paddle switch, and the -10dB pads are below them. The switches are push-on push-off types. The pads are in-circuit when the switches are depressed. Depress the -10dB switches to select the -10dB pads. To select the -20dB pads both sets of switches (-10 and -20) must be depressed (depressing only the -20 switches will have no effect).

Changing The Orientation Of The Phono/Line Switches

Using a 2mm Allen key undo and remove the 3 Allen screws around the edge of the circular switch mounting plate. The switch plate can now be rotated in 15-degree steps. The plate can be re-attached to the subframe with the Allen screws when a convenient angle has been chosen.

Replacing The Faders

Using a 2mm Allen key undo and remove the 3 Allen screws (the X-F Monitor fader has only 2 screws) which secure the fader mounting plate to the subframe. Carefully withdraw the fader, taking care not to damage the wiring harness that is attached to it. Unplug the 3-pin connector, wiggle the plug from side to side as you pull the plug from the socket. Plug the connector into the new fader. The connector is keyed so that it cannot be inserted the wrong way round. Carefully place the new fader back into the subframe and secure with the Allen screws removed earlier, DO NOT OVER-TIGHTEN THE SCREWS.

Replaceable Spares Part Numbers

RS2331 - Urei 1601/S Sampler Spares Assembly

RS2332 - Urei 1601/S Fader Spares Assembly

RS2333 - Urei 1601/S Phono/ Line Switch Spares Assembly

RS2334 - Urei 1601/S X-Fader Mon Spares Assembly

RS2335 - Urei 1601/S EQ L&R Spares Assembly

14

Image 14
Contents Page Potters BAR Contents Important Safety Instructions Green and Yellow US Green/Yellow TIP Safety Symbol GuideHeadphones Safety Warning Introduction Page Mains Installation InstallationGeneral Precautions Shielding Initial Wiring ConsiderationsAudio Wiring Points to Remember Working Safely with SoundUnpacking and Inspection Inspection and InstallationPowering Environmental ConsiderationsConnecting to a Typical Sound System Making Adjustments and Fitting Spares Setting The Pre-trim PadsPage Description TOP Panel 1601S ShownPage Rear Connector Panel 1601S Shown Front Panel EQ CUT -RotaryGetting Started Combi -XLR ConnectorOperation MIC / Line InputEQ -HIGH Control Level ControlEQ -LOW Control PRE-TRIM Pads Input Selector SwitchesClip Indicators HI EQ Channel Volume FadersTrim MID EQRecord OUT FX Send & Return / AUXSend -LEVEL Send -SELECTFX SEND/RETURN RE-CONFIGURATION Clip IndicatorFX ON/OFF Switch Return / AUX -LEVELMaster / Booth Output Fader Curve FaderExciter MASTER/CUE Select Headphone MonitorLevel Monitor Sampler 1601S only ControlsLocking Onto the Beat Selecting the Sampling Source Recording ModeRecording Loops Reverse Mode Play ModeShot Mode PLAYING-BACK LoopsDisengaging the BPM Engine Loop Synchronisation AdjustmentsSampler Specification Rule of ThumbBlock Diagram Connecting Leads Troubleshooting Specifications Warranty Glossary Post after the channel faderEqualising the system to notch out the offending frequencies Riaa