Yamaha MD4S owner manual Appendix

Page 107

110 Appendix

SCMS (Serial Copy Management System)—A protection system intended to prevent illegal copying of music. SCMS allows one-time serial copying of copy-protected material. If the source is not copy protected, it’s possible to make any number of digital-to-digital copies of the material. If the source is copy protected, however, it’s possible to make a first-generation copy, but further copies cannot be made from the first-generation copy. SCMS is only effective when copying via digital connections. Recordings made via analog connections are not affected.

Signal to Noise Ratio (S/N)—In an audio system, the difference between the nominal sig- nal level and the residual noise floor, usually expressed as a ratio in decibels. It’s used as a mea- sure of an audio system’s noise performance.

Tempo Map—A map containing the tempo and meter information for a song.

TOC—An acronym for Table Of Contents. An area of the MD DATA disc used to store infor- mation about what is recorded on the disc, the disc title, song titles, and so on.

Tracking—A “track” is an area used to record and playback an individual audio signal. The MD4S has four tracks, each of which can be recorded/played independently. Recorders like the MD4S which have multiple tracks are called “multi-track recorders” (MTR).

Unity Gain—A gain of one. That is, the signal is output from a circuit at the same level at which it entered. Once passed the MIC/LINE amplifier, a unity gain system minimizes signal noise and distortion. The unity gain position for the MD4S faders is at the 7–8 mark.

—Owner’s Manual

Image 107
Contents Multitrack MD Recorder Varoitus Safety Instructions Read the Following Before Operating the MD4S Copyright Keep This Manual For Future ReferenceOperating Notes Recorder MD4S FeaturesMixer MD Data and MiniDisc Buying discs for the MD4SRecording modes and recording times To update the TOCMD4S songs and blank areas Gain control Flip switchFront and rear panel Mono InputsPAN control CUE PAN/CUE Level controlsEQ controls AUX controlMonitor/Master section Stereo InputsDisc transport buttons Disc transport sectionLast REC Search IN/OUT, SET buttons Auto Punch I/O buttonSong Search / buttons B repeat buttonExit button Peak Hold buttonDisplay button Function buttonsDisplay TOC Edit indicatorStatus indicators Pitch indicatorTrack recording indicators Time counter modeMidi indicators CUE MIX indicatorRepeat indicator Auto punch indicatorIN, OUT indicators Marker indicatorsMIC/LINE Input 3, 4 jacks Top panel connectorsMIC/LINE Input 1,2 jacks Insert I/O jacksRear panel Punch I/O jack Midi IN, OUT, Thru connectorsFront panel Phones jackExample connections Before you beginPreparations for recording Recording the first track Direct RecordingTurning on the MD4S Inserting a discCheck the recording level Find a blank areaSelect the track for recording Begin recording Monitor the signal being recorded on the trackStart recording Press the Last REC Search in button Listening to the first trackSelect the track to record OverdubbingPress the Play button to begin recording Start recordingListen to the recording Mixdown Connecting a master recorderAdjust the mix balance of each track Turn on the Monitor Select Stereo switchListen to the master recording Press the Monitor Select 2TR in switchRecord to your master recorder After completing the Basic Operation section Advanced techniques on the MD4S 4 a B C Mixing multiple channels as you recordConnect the audio sources to MIC/LINE Input jacks Turn on the Monitor Select CUE switchSignal flow when mixing multiple channels Ping-pong recording Set the Flip switches of input channels 1-4 to PB Signal flow for ping-pong recording Connect your audio sources to MIC/LINE Input jacks 1 Adding sounds during mixdownMake preparations for mixdown Turn on the CUE MIX to Stereo switch Applying effects Using the Insert I/O jacksExternal effect connections when using an insertion cable Output jack L Input jack Using the AUX Send jacksRaise level control 5/6 Applying effects during mixdownApplying an effect during ping-pong recording Raise level control 5/6 Raise the CUE Level controls of input chan- nels Applying an effect only to the monitor signalST Bus Manual punch-in/out Punch-in/out using the REC buttonPress the REC button and adjust the recording level Punch-in/outMake preparations for manual punch-in/out Punch-in/out using REC SelectPress the foot switch once again to enter pause mode Punch-in/out using a foot switchPress the foot switch Specify the auto punch-in/out points Setting the pre-roll/post-roll timesAuto punch-in/out Press the Enter button Single-take auto punch-in/outPress the Auto Punch I/O button Press the Play button to hear the recorded result When stopped or paused, press the REC buttonPress the Play button to begin the actual auto punch-in/out Multi-take auto punch-in/out Press the Play button to begin auto punch-in/out From a stopped or paused condition, press the REC buttonWith Next Take shown in the display, press the Enter button Press the Enter button once again to finalize the take Locating to a specified time Press the Display button to switch the time counter modeQuick search functions Searching for songsSearching for Markers Locating to the Last Record In/Out PointPress the TOC Write button to update the TOC Cursor shuttle Display Playback volume Rotate the Data dial toward the right Erasing a marker or auto punch-in/out pointRotate the Cursor shuttle toward the right Play forward/backward at various speeds Cue/Review Various playback functionsPlaying a song repeatedly One Song Repeat/All Song Repeat Playback at half speed x1/2 PlayPress the Enter button to begin programming the cue list Repeating a specific portion of a song A-B RepeatCue List playback Rotate the Data dial to select either Edit List or NEW ListPress the Play button to begin Cue List playback Press the Enter button once againOriginal song Creating a new song from a Cue List Cue List CopyPress the Enter button to begin programming Programming the song playback order Program PlayRotate the Data dial to select either Edit Prog or NEW Prog Press the Play button to begin Program Play Locate to the copy destination, and stop or pause playback Editing functionsCopying a portion of a track Part Copy Erasing a section of a track Part Erase Press the Enter button to execute the Part Erase operation Copying an entire track to another track Track CopyCopying/converting a song Song Copy Erasing an entire track Track EraseRotate the Cursor shuttle to the right 4T1234 2T12Press the Enter button to execute the Song Copy operation Erasing a song Song EraseSplitting a song into two Song Divide Rotate the Data dial to select the songs that will be joined Joining divided songs together Song CombineMoving a song Song Move Exchanging the order of songs Song Renumber Before Song Renumber Press the Pitch button Adjusting the record/playback pitch Pitch functionOther functions Titling discs and songs Erasing a disc Disc Erase Viewing disc contentsPress the Song Search button to select a blank area Changing the recording modeRotate the Data dial to select either 86 or Adjusting the display brightnessRotate the Data dial to adjust the brightness Selecting the type of Frame displayFlashing Using a Foot switchSynchronizing the MD4S with a Midi sequencer Connecting the MD4S with a Midi systemMidi functions Rotate the Data dial to make the display read MTC Master Synchronization using MTCTransmit MTC from the Midi OUT connector of the MD4S About MTC and Midi ClockRotate the Data dial to make the display read Midi Clock Synchronization using Midi ClockMidi sequencer settings Transmit Midi Clock from the Midi OUT connector of the MD4SCharacter a that indicates the step will blink Synchronizing two MD4S recorders Synchronized recording on a slave MD4S Settings for the MTC Slave MD4SRotate the Data dial to make the display read MTC Slave Start the master MD4S running play/record/rehearsal Start the master MD4S playback/record/rehearsalSynchronized playback of a slave MD4S Press the Play button on the slave MD4SPress the Utility button to return to normal operation Synchronizing to MTC with a specified offset time differenceControlling the MD4S by MMC Switching MMC reception on/offRotate the Data dial to switch the setting on or OFF Press the Enter button to confirm the settingSetting the MMC Device ID Section How many songs can I store on an MD Data disc? TroubleshootingDo I have to clean the MD4S heads? Do I have to sacrifice one track to record timecode?Cannot use the punch-in/out Blank Display MessagesAuto Punch Record Standby Modes of the MD4S transportSpecifications General DimensionsBlock Diagram Glossary Glossary Appendix Tempo Map Chart Midi Implementation Chart Numerics IndexSong Search Tracking Sheet