Yamaha MD4S owner manual Varoitus

Page 2

FCC INFORMATION (U.S.A.)

1.IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2.IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3.NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

Laser Diode Properties

*Material : GaAlAs

*Wavelength : 780–790 nm

*Emission Duration : Continuous

*Laser Output Power : Less than 44.6 ∝W (Note) Laser output is measured at a

distance of 20cm from the object lens on the optical pick-up head.

 

This unit is classified as a

CLASS 1 LASER PRODUCT

Class 1 laser product.

This label is located on the

LUOKAN 1 LASERLAITE

exterior.

KLASS 1 LASERAPPARAT

 

 

Klassmärkning för Finland.

 

 

• On USA or Canadian

CAUTION

: INVISIBLE LASER RADIATION WHEN OPEN.

models do not have this

 

AVOID EXPOSURE TO BEAM.

label.

VARNING

: OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

 

ÖPPEND. STRÅLEN ÄR FARLIG.

• This label is located on

VARO!

: NÄKYMÄTÖNTÄ AVATTAESSA OLET ALTTIINA

 

LESERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

the interior.

VARNING

: OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

 

ÖPPNAD. BETRAKTA EJ STRÅLEN.

• Varningsanvisning för

VORSICHT! : UNSICHTBARE LESERSTRAHLUNG WENN ABDECKUNG

laserstrålning. Placerad

 

GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

i apparaten.

IMPORTANT

Please record the serial number of this unit in the space below.

Serial No.:

The serial number is located on the bottom or rear of the unit. Retain this Owner's Manual in a safe place for future reference.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of the three pin plug.

*This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD.

CAUTION

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

ADVARSEL

Usynlig laserstråling ved åbning. Undgå udsaettelse for stråling.

VAROITUS

Laitteen käyttäminen muulla kuin tässä käyttöohjeesa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING

Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Multitrack MD Recorder Varoitus Safety Instructions Read the Following Before Operating the MD4S Copyright Keep This Manual For Future ReferenceOperating Notes Recorder MD4S FeaturesMixer Buying discs for the MD4S MD Data and MiniDiscTo update the TOC Recording modes and recording timesMD4S songs and blank areas Mono Inputs Flip switchFront and rear panel Gain controlAUX control CUE PAN/CUE Level controlsEQ controls PAN controlStereo Inputs Monitor/Master sectionDisc transport section Disc transport buttonsB repeat button Auto Punch I/O buttonSong Search / buttons Last REC Search IN/OUT, SET buttonsFunction buttons Peak Hold buttonDisplay button Exit buttonPitch indicator TOC Edit indicatorStatus indicators DisplayCUE MIX indicator Time counter modeMidi indicators Track recording indicatorsMarker indicators Auto punch indicatorIN, OUT indicators Repeat indicatorInsert I/O jacks Top panel connectorsMIC/LINE Input 1,2 jacks MIC/LINE Input 3, 4 jacksRear panel Phones jack Midi IN, OUT, Thru connectorsFront panel Punch I/O jackBefore you begin Example connectionsInserting a disc Recording the first track Direct RecordingTurning on the MD4S Preparations for recordingCheck the recording level Find a blank areaSelect the track for recording Begin recording Monitor the signal being recorded on the trackStart recording Listening to the first track Press the Last REC Search in buttonOverdubbing Select the track to recordPress the Play button to begin recording Start recordingListen to the recording Turn on the Monitor Select Stereo switch Connecting a master recorderAdjust the mix balance of each track MixdownListen to the master recording Press the Monitor Select 2TR in switchRecord to your master recorder After completing the Basic Operation section Advanced techniques on the MD4S Mixing multiple channels as you record 4 a B CTurn on the Monitor Select CUE switch Connect the audio sources to MIC/LINE Input jacksSignal flow when mixing multiple channels Ping-pong recording Set the Flip switches of input channels 1-4 to PB Signal flow for ping-pong recording Connect your audio sources to MIC/LINE Input jacks 1 Adding sounds during mixdownMake preparations for mixdown Turn on the CUE MIX to Stereo switch Using the Insert I/O jacks Applying effectsExternal effect connections when using an insertion cable Using the AUX Send jacks Output jack L Input jackApplying effects during mixdown Raise level control 5/6Applying an effect during ping-pong recording Raise level control 5/6 Applying an effect only to the monitor signal Raise the CUE Level controls of input chan- nelsST Bus Punch-in/out Punch-in/out using the REC buttonPress the REC button and adjust the recording level Manual punch-in/outPunch-in/out using REC Select Make preparations for manual punch-in/outPress the foot switch once again to enter pause mode Punch-in/out using a foot switchPress the foot switch Specify the auto punch-in/out points Setting the pre-roll/post-roll timesAuto punch-in/out Press the Enter button Single-take auto punch-in/outPress the Auto Punch I/O button Press the Play button to hear the recorded result When stopped or paused, press the REC buttonPress the Play button to begin the actual auto punch-in/out Multi-take auto punch-in/out Press the Play button to begin auto punch-in/out From a stopped or paused condition, press the REC buttonWith Next Take shown in the display, press the Enter button Press the Enter button once again to finalize the take Searching for songs Press the Display button to switch the time counter modeQuick search functions Locating to a specified timeLocating to the Last Record In/Out Point Searching for MarkersPress the TOC Write button to update the TOC Cursor shuttle Display Playback volume Rotate the Data dial toward the right Erasing a marker or auto punch-in/out pointRotate the Cursor shuttle toward the right Various playback functions Play forward/backward at various speeds Cue/ReviewPlayback at half speed x1/2 Play Playing a song repeatedly One Song Repeat/All Song RepeatRotate the Data dial to select either Edit List or NEW List Repeating a specific portion of a song A-B RepeatCue List playback Press the Enter button to begin programming the cue listPress the Enter button once again Press the Play button to begin Cue List playbackCreating a new song from a Cue List Cue List Copy Original songPress the Enter button to begin programming Programming the song playback order Program PlayRotate the Data dial to select either Edit Prog or NEW Prog Press the Play button to begin Program Play Locate to the copy destination, and stop or pause playback Editing functionsCopying a portion of a track Part Copy Erasing a section of a track Part Erase Copying an entire track to another track Track Copy Press the Enter button to execute the Part Erase operationErasing an entire track Track Erase Copying/converting a song Song Copy4T1234 2T12 Rotate the Cursor shuttle to the rightErasing a song Song Erase Press the Enter button to execute the Song Copy operationSplitting a song into two Song Divide Joining divided songs together Song Combine Rotate the Data dial to select the songs that will be joinedMoving a song Song Move Exchanging the order of songs Song Renumber Before Song Renumber Press the Pitch button Adjusting the record/playback pitch Pitch functionOther functions Titling discs and songs Viewing disc contents Erasing a disc Disc EraseChanging the recording mode Press the Song Search button to select a blank areaSelecting the type of Frame display Adjusting the display brightnessRotate the Data dial to adjust the brightness Rotate the Data dial to select either 86 orUsing a Foot switch FlashingSynchronizing the MD4S with a Midi sequencer Connecting the MD4S with a Midi systemMidi functions About MTC and Midi Clock Synchronization using MTCTransmit MTC from the Midi OUT connector of the MD4S Rotate the Data dial to make the display read MTC MasterTransmit Midi Clock from the Midi OUT connector of the MD4S Synchronization using Midi ClockMidi sequencer settings Rotate the Data dial to make the display read Midi ClockCharacter a that indicates the step will blink Synchronizing two MD4S recorders Synchronized recording on a slave MD4S Settings for the MTC Slave MD4SRotate the Data dial to make the display read MTC Slave Press the Play button on the slave MD4S Start the master MD4S playback/record/rehearsalSynchronized playback of a slave MD4S Start the master MD4S running play/record/rehearsalSynchronizing to MTC with a specified offset time difference Press the Utility button to return to normal operationPress the Enter button to confirm the setting Switching MMC reception on/offRotate the Data dial to switch the setting on or OFF Controlling the MD4S by MMCSetting the MMC Device ID Section Do I have to sacrifice one track to record timecode? TroubleshootingDo I have to clean the MD4S heads? How many songs can I store on an MD Data disc?Cannot use the punch-in/out Display Messages BlankModes of the MD4S transport Auto Punch Record StandbySpecifications Dimensions GeneralBlock Diagram Glossary Glossary Appendix Tempo Map Chart Midi Implementation Chart Index NumericsSong Search Tracking Sheet
Top Page Image Contents