Peavey Supreme Back Panel Features External Speaker Jacks, Impedance Selector Switch, Preamp OUT

Page 5

Back Panel:

BACK PANEL FEATURES

EXTERNAL SPEAKER JACKS (21)

Provided for connection of external speaker cabinet. Minimum external speaker impedance A is 8 ohms (4 ohm total impedance).

IMPEDANCE SELECTOR SWITCH (22)

Used to select the appropriate impedance of the speaker enclosure(s). If two enclosures of equal impedance are used, the switch should be set at one half of that value (e.g., for two 16 ohm enclosures, set switch to

8 ohms; for two 8 ohm enclosures, set switch to 4 ohms).

PREAMP OUT (23)

The preamp out can be used to route the amplified signal to a mixing console, tape recorder, etc. Connect the preamp output using a shielded cable to an input of the tape recorder, mixer, etc. This patch does not affect the operation of the amplifier.

POWER AMP INPUT (24)

Used to connect line level signal to the power amplifier.

REMOTE SWITCH JACK (25)

Provided for the connection of the supplied remote footswitch. The footswitch is used to select the Lead or Normal channels and defeat effects loop. When using remote footswitch, always insert the plug fully (second click) to insure proper operation.

GROUND SWITCH (26)

Three position rocker-type switch, which, in most applications, should be operated in its center or zero position. There may be some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative (+or -) or until the noise is minimized.

NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS.

LINE CORD (120 V PRODUCTS ONLY) (27)

For your safety, we have incorporated a three-wire line (mains) cable with proper grounding A facilities. It is not advisable to remove the ground pin under any circumstances. If it is neces-

sary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is oper- ated with the proper grounded receptacles.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents TRAN8TUB~~ ~G-u~xEsP a m p H e a d Literature accompanying the product Power LED Front Panel Features Power SwitchResonance Switch Effects Level SwitchThrash Switch Gain SwitchChannel Select Switch Bright SwitchImpedance Selector Switch Back Panel Features External Speaker JacksPower AMP Input Remote Switch JackPreamp Section Flowchart Power LED LED indicador de corriente Power Switch Interruptor de corrienteResonance Switch Conmutador de resonancia Effects Level Switch Conmutador de nivel de efectosChannel Select Switch Interruptor para seleccih del canal Gain Switch Interruptor de gananciaBright Switch Interruptor de brillo Volume El volumenPreamp OUT Salida de preamplificador Power AMP Input Entrada del amplificador de potenciaRemote Switch Jack Enchufe hembra de interruptor remoto Power LED DEL tkmoin de mise sous tension Power Switch Interrupteur d’alimentationDynamics Control Commande CcDynamique Tjb Resonance Switch Commutateur de rbonanceThrash Switch Commutateur anti-emballement Gain Switch Interrupteur de gainChannel Select Switch Selecteur de canal Bright Switch Selecteur de brillancePreamp OUT Sortie preampli Power AMP Input Entree ampli de puissanceRemote Switch Jack Prise pour interrupteur a distance Power LED Kontrollampe Power Switch NetzschalterResonance Switch Resonanzschalter Effects Level Switch EFfects-pegelschalterChannel Select Switch Kanal auswtihlenschalter Thrash Switch Thrash schalterLOW Gain Input Tiefen gain-eingang High Gain Input H6hen gain-EingsngPower AMP Input Leistungsverstarkereingang Impedance Selector Switch Impedanz-WahlschalterRemote Switch Jack Buchsen fur fern ful3schalter RiickplattePage Peavey ONE-YEAR Limited WARRANTY/REMEDY Important Safety Instructions Peavey Electronics
Top Page Image Contents