Vx Master Section, Aux Out Led | Peavey Century Series specs

CENTURY SERIES

Vx Master Section

Comprises four modules and is the control center for the Vx console. Stereo Aux In, Monitoring, Solo, Talkback, Stereo Program In, Master Aux & Matrix, internal oscillator & Scene Muting functions are controlled here.

LEFT/RIGHT Modules

Stereo Aux In HF Level

Upper-band fixed frequency (10kHz) EQ that affects the asso- ciated Stereo Aux in channel.

Stereo Aux In LF Level

Lower-band fixed frequency (80Hz) EQ that affects the associ- ated Stereo Aux in channel.

Stereo Aux In LEV Control

Controls the level of the Stereo Aux In audio.

Stereo Aux In MUTE Switch w/LED

Turns off the audio assigns to the main mixes

Stereo Aux In MONO Switch

Assigns the audio to the Mono bus.

L/R/MONO MUTE Switch w/LED

Mute outputs of Left, Right & Mono signals respectively.

MONO Switch w/LED

Assign the Left and Right signals to the Mono output.

MATRIX POST Switch w/LED

Switches the source of Left, Right and Mono matrix feed sig- nals between pre and post-fader.

L/R PEAK/SIG LED's

The red LED lights 3dB before clipping point and responds to pre and post fader levels. The varying intensity of the green LED displays the level of the mix bus audio.

SOLO Switch w/LED

Solo monitoring of the L, R or Mono Output. Choice of PFL or AFL source.

Fader

100mm linear analog fader for control of the output level to XLR, matrix and Solo AFL.

Not Shown:

Stereo Aux In L+R Switch

Assigns the stereo audio to the main L+R mixes, L to L, R to R.

Stereo Aux In SIGNAL LEDs

Bi-color LED lights green at normal output levels, red indi- cates an overload condition. Responds to audio in both L&R channels, and pre and post level control.

Stereo Aux In SOLO Switch w/LED

Allows SOLO monitoring of the associated Stereo Aux In sig- nal. Choice of PFL or AFL.

Auxiliary Output MUTE w/LED

Mutes the respective auxiliary XLR output. In addition the Aux Scene Mute Master facility allows a number of auxes to be muted at the same time. The mute LED indicates the audio status and responds to both controls. Refer to the Special Facilities section for more about Aux Scene Mute.

Aux Master LEV Control

Controls final output signal level of the auxiliary output.

Aux Master GLOBAL PRE Switch w/LED

This switch changes all Aux sends on input modules for the associated Aux bus to be Pre-Fader or Post-Fader. Up=Pre, Down=Post. The associated LED is green in color.

Left, Right & Mono Insertion points. Left, Right & Mono Meters.

MONO Module

Lamp Dim Control

Controls the intensity of the lighting devices plugged into the XLR sockets on the back of the meter bridge.

Power Indicators

These four LED’s indicate the status of the incoming DC.

Stereo Program In Gain

Adjusts the gain of the Stereo Program In signal.

Stereo Program In EQ

Two-band fixed frequency (10kHz and 80Hz) EQ that affects the Stereo Program

AUX 1&2, 3&4, 5&6, 7&8 Levels

These rotary faders controls the amount of Stereo Program sig- nal sent the respective Aux buses. Normally Left signal is sent to the odd Aux buses, while Right signal is sent to the even Aux buses. Refer to Special facilities for more information.

Stereo Program Balance

Provides adjustment of the image position.

Stereo Program Assignments

Assigns the Stereo Program to the Mono and Left/Right buses.

AUX OUT LED

Bi-color LED lights green at normal output levels, red indi- cates an overload condition.

Aux SOLO Switch w/LED (green)

Solo monitoring facility for the AUX mix. Choice of PFL or AFL.

AUX MUTE ACTIVE LED

Indicator for the Aux Scene Mute facility. Illuminates when the Aux Scene Mute Master switch has been selected.

Stereo Program Mute w/LED

Mutes the output of the Stereo Program.

Stereo Program Level

Controls final output signal level of the Stereo Program.

Stereo Program SIG/PEAK LED

The red LED lights 3dB before clipping point and responds to pre-fader levels. The varying intensity of the green LED dis- plays the level of the audio. Both LEDs respond to the sum of L&R audio.

PAGE 21