Peavey Century Series owner manual VX User Options, Module Location Option Title Function

Page 34

VX

CENTURY SERIES

VX User Options

VX consoles are shipped having standard configuration unless specified at time of order. These are ways that the console config- uration may be varied after manufacture. The items listed are internal options selected by gold jumper links or pcb DIP switches. DIP switch 'ON' position is down when reading the numbers on the switch body.

Jumper link default is marked with a line on the board and is usually pins 1&2 of the three pin header.

In addition there are links for module function assignment. Take care to not disturb these when using USER OPTION links.

MODULE

LOCATION

OPTION TITLE

FUNCTION

 

M=Main board

 

 

 

C=Connector

 

Shipped with option underlined

Inputs

M

J2, Pre Feed 1: Mute ?

Aux sends with Mute or without Mute

 

M

J3, Pre Feed 1: Source

Aux sends Pre or Post EQ

 

M

DIP switch 1-7

Aux 1-7 override Global Pre (local Pre)

 

M

DIP switch 8

Aux 8 Direct Out = Pre Feed 1 or 2

 

M

J4, Pre Feed 2 (never mute)

Aux 8 Direct source, Pre EQ or Pre-fader

 

M

J5, Input Meter Source

Preamp, Pre-fader, Post-fader

VX Stereo In

C

behind GAIN pot

Phase invert: L only or L+R

 

M

J4: Aux Pre Source

with MUTE or without MUTE

 

M

J2: Left Pre Source

Pre EQ or Pre Fader

 

M

J3: Right Pre Source

Pre EQ or Pre Fader

VX Multi Input

 

same as Stereo Input

 

VX Groups

M

SEL 4: VCA Mute Atten

VCA mute affects Ch Mute; VCA mute affects Ch VCA

 

C

Insert: selector switch

Group insert or Matrix insert

VX L & R

C

Connector board SEL 4

feed to ALT (Mono module) Pre or Post insert

 

M

SEL 3 Aux local Mute

Link on = Enable, or Link off = Master Mute only

VX Mono

M

SEL1,3,5,7,9,11,13,15

Stereo Prog In: Aux Stereo or Mono

 

M

SEL2,4,6,8,10,12,14,16

Stereo Prog In: Aux Send On or Off

VX Master

C

SEL1 TB Phantom Power

On or Off

 

C

SEL2 TB Gain select

20, 30, 40dB gain

IMPORTANT

Group Modules and Left/Right Modules are pre-assigned at the Crest factory

These modules must always be installed in the correct positions. They are NOT interchangeable without being properly re-

assigned. Please contact the Crest Audio Service Department for more information.

APPENDIX A

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Century Series Crest Audio Inc Table of Contents Feature Overview Vx featuresAn introduction to VCAs Wet / Dry Blending TIP Left Ring Right Sleeve Common Wiring ConventionsTIP Positive Ring Negative Sleeve Ground TIP Send Ring Return Sleeve GroundRear Connections ALT OUT R Tape in RSTR PGM R Mntr OUT RCentury Series Console Power Supply Power Connections Console CoolingSystem Connections Input ConnectionsOutput Connections Vx Input Module PAN Control VCA LEDThree-Band Sweep Equalizer Controls Vx Stereo Input ModuleGain & R Gain Controls AUX Sends 1- 8 indiv. level controlsSUM Solo Optional Multi-Input Module Rear panel connectionsAudio Group PEAK/SIG LED Vx Group ModulesUnity LED Program AUX OUT LED Vx Master SectionAUX Mute Active LED Pink Noise Switch w/LED Stereo Program Solo Switch w/LED10kHz/1kHz/100Hz switches Oscillator on Switch w/LEDAUX Meters Vx Meter Bridge 52 & 64 Frame ModelsVx Meter Bridge 44 Frame Model Special Facilities Stereo Program Input Special Facilities contdLCR Panning VCA Group MutesPage Appendix a Technical Information Configurations General Specifications Vx ConsoleArchitect’s & Engineer‘s Specifications Vx Console DiagramVx Block Console Rear Views & Dimensions VX User Options Module Location Option Title FunctionTWO Remove front module screw Console DisassemblyONE Open the armrest Three Remove rear screwsPage Appendix B Schematics Crest Audio Inc
Top Page Image Contents