Korg MS2000R manual Timbre2 Dual/Split

Page 77

Timbre2 (Dual/Split)

PITCH

Transpose:

Tune:

Vibrato Int:

Bend Range:

VOICE

Assign :

Priority:

Trigger :

Detune:

 

EG 1

 

 

EG Reset:

SEQ COMMON

SEQ1

LastStep :

 

 

Knob:

SeqType:

 

 

Motion:

Run Mode:

 

 

 

Key Sync:

 

 

Resolution :

 

SEQ2

 

 

Knob:

 

 

Motion:

SEQ3

Knob:

Motion:

FILTER

Vel.Sense:

EG 2

EG Reset:

AMP

Vel Sense:

KBD Track:

LFO 1

LFO 2

KeySync:

KeySync:

Tempo Sync:

Tempo Sync:

Sync Note:

Sync Note:

Appendices

71

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Page Location Power supplyInterference with other electrical devices FCC Regulation Warning for U.S.AHow this manual is organized About this manualPrinting conventions in this manual IiiTable of Contents Parameter Guide About Midi How Resolution and Sync Note values correspondBasic Guide Basic GuideModes Main featuresStructure MS2000/MS2000R Synth programs How a program is structuredOSC1/OSC2/NOISE EG1/2Audio in 2 jack modulator Vocoder programsOSC1/NOISE/AUDIO in 1 jack carrier MS2000 MS2000R Front panelKnob POWER/VOLUME knobWave key Control 1 knobLCD Edit and Global modes, this will display parameters Original Value LEDLCD Phones jack MS2000R Rear panelSelect 1-16 keys Cable hook Control panel MS2000Pitch Bend wheel Modulation wheelConnecting external devices Connecting the AC adapterConnecting pedals and switches Connecting Midi devicesConnecting the MS2000 to a computer/ sequencer Setting the Midi channel preparations for playingConnecting the MS2000R to a com- puter/sequencer Connections to a computer/ sequencerListen to the demo perfor- mance Select a program Playing a programMS2000 Selecting a program Using the BANK/OCTAVE UP Down keys and the Select 1-16 keysUse the Select 1-16 keys to play the program Changing the pitch sounded by the keys in one-octave stepsPlay a program in which the arpeggia- tor is turned on Using the knobs and keys to modify the settingsPlaying arpeggios Playing a program in which MOD Sequence is on Using MOD Sequence to modify the soundChecking the parameter that is assigned to each sequence Checking the value recorded for each stepUsing the vocoder function Using external inputUsing an internal waveform as the carrier Using an external waveform as the carrierEditing in Program Play mode Basic editing proceduresEditing in LCD Edit mode Editing program parametersReturning to the state before editing Switching timbresCompare Writing saving an edited programSpecify how notes will be sounded Make oscillator settingsEditing a synth program Set the volume of each oscillator Make filter settings Specify time-varying change in the tone Adjust the output of the timbreSpecify time-variant changes in volume Apply modulation to parameters Virtual Patch Make LFO settingsSpecify sequence data for each step Make MOD Sequence settingsSet SEQ Common parameters Editing effect parameters Modulation effect settingsEditing arpeggio parameters Delay settingsSet the filter Adjust the mic input audioEditing vocoder program Changing the program name Restoring settings to their factory state Basic editing procedureEditing Global parameters Editing parametersSynchronizing an external Midi device to the MS2000/MS2000R Synchronization with external Midi devicesSaving data on an external device Data Dump Screen will ask you to confirm the data transmis- sion Program parameters Global parameters Parameter Guide+3, 2+2, 3+1 Page01 CommonPage02 Name VoicePage03 Voice GLBOscillator PitchPage04 Pitch Page05 OSCDwgs Page06 OSC MixerPage07 Mixer OFFPage08 Filter FilterEG Envelope Generator AMP AmplifierPage09 AMP Page10 EG Page11 EG32...1/1 LFO Low Frequency OscillatorPage12 LFO Page13 LFO MOD Sequence Virtual PatchPage14 PATCH1 Page15 PATCH2 Page16 PATCH3 Page17 PATCH4 Page18 SEQ CommonPage21 SEQ3 Page19 SEQ1Page20 SEQ2 Effects Page23 Delay FXPage22 MOD FX Page24 EQPage25 Arpeggio ArpeggiatorPage26 Utility UtilityCopySeq SwapTimbreInitSeq Swap Seq CopySeqAllSwapSeq Page06 Audio AudioWave  Saw...Audio Control1  000 127 Control2  Threshold  000...127AMP CH Param Init ch Pan Init ch Lvl430.0Hz...450.0Hz Page1 Global001...127 ConstInternal...Auto Page2 Memory Page3 MidiPreload A00...H16 Page4 Midi FilterChg Page6 PEDAL&SW Page5 Ctrl ChangePage8 Calib Page7 User ScaleMidi channels About MidiProgram change AftertouchControl changes Bn, cc Control changesGate values Parameters transmitted and received via NrpnControlling the arpeggiator Controlling the Virtual Patch 1-4 Source Other controlsControlling the Virtual Patch 1-4 Destination Controlling the FC MOD source of a vocoder program FilterSEQ2/CH PAN System exclusive messages Transmitting sound settings etc. Data Dump Wave CC#77 Front panel knob/key control change assignmentsOSC 2 Semitone values Control 2 values when OSC 1 Wave = DwgsSEQ Arpeggiator Voice Name ListD01 Ana Fuzz Synth Hard Single G01 Square Comp Synth Hard Single Program No Program Name Blank chartTimbre2 Dual/Split Vocoder Program Specifications and options TroubleshootingIndex SymbolsLatch Delay FX LFO Midi Implementation Chart
Top Page Image Contents