Fujitsu MB15E07SL manual Fujitsu Limited, F0306

Page 26

MB15E07SL

FUJITSU LIMITED

All Rights Reserved.

The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering.

The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information.

Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party’s intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein.

The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).

Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.

Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions.

If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan.

F0306

FUJITSU LIMITED Printed in Japan

Page 25 Page 26
Image 26
Page 25 Page 26
Contents Packages FeaturesDescription Pin plastic Ssop Pad plastic BCC FPT-16P-M05 LCC-16P-M06FPT-16P-M05LCC-16P-M06 PIN AssignmentsPin Ssop Pad BCC Name PIN DescriptionsPin no Descriptions Block Diagram SW FC LDSAbsolute Maximum Ratings Parameter Symbol Condition Rating Unit Remark MinParameter Symbol Value Unit Remark Min Recommended Operating ConditionsElectrical Characteristics Parameter Symbol Condition Value Unit Min TypVp/2 Vp − 0.5 V Vp Charge Pump Output Voltage Pulse Swallow Function Shift Register Configuration Programmable Reference CounterFunctional Description Serial Data Input16383 Binary 7-bit Swallow Counter Data Setting Divide ratio aProgrammable Counter 2047LD/fOUT output signal PS Pin Setting PS pin Status Power Saving Mode Intermittent Mode Control CircuitZC Pin Setting ZC pin Do output Normal output Do Output ControlOFF Serial Data Input Timing Parameter Min Typ Max UnitPhase Comparator Output Waveform Measurment Circuit for Measuring Input Sensitivity fin/OSCIN Typical Characteristics Fin input sensitivityOscin input sensitivity MA mode Do output currentFin input impedance Oscin input impedancePLL Reference Leakage PLL Phase NoiseReference Information 500.0 ∝s/div Application Example Part number Package Remarks Usage Precautions Ordering Information 16-pin, Plastic Ssop FPT-16P-M05Pin plastic Ssop FPT-16P-M05 Package DimensionsFujitsu Limited F16013S-c-4-6 Dimensions in mm inches Pad plastic BCC LCC-16P-M06 Index AreaFujitsu Limited F0306
Top Page Image Contents