Stanley Black & Decker Complete Guide to Operating Your Stanley Trachorse Lawn Mower
Page 14

OPERATION

5.Turn the ignition switch clockwise to begin cranking the engine. Use short starting cycles (15 seconds per minute) to prolong starter life. Extended crank- ing can damage the starter motor.

6.After the engine starts, allow it to warm-up for a few seconds before moving the choke. Move the choke inward in small steps to allow the engine to accept small changes in speed and load. Continue moving the choke in until it is fully off and the engine is run- ning smoothly.

7.Place the throttle at the maximum setting.

8.Position each tool circuit switch to 5 GPM. The tools can now be used.

9.Reverse the above procedure to stop using the tools.

DUAL CIRCUIT COMBINED FOR 10 GPM

1.To combine the two 5 GPM tool circuits into one 10 GPM tool circuit, connect the PRESSURE FLUID

OUT hose to either one of the two male couplers. Connect the RETURN FLUID IN (RETURN) hose to either one of the two male couplers. Connect the other ends of the hoses to the tool.

2.Ensure the throttle control is pulled fully back to the idle position.

3.Ensure the tool circuit switches are in the OFF posi- tion.

4.Pull the choke out until it stops.

5.Turn the ignition switch clockwise to begin cranking the engine. Use short starting cycles (15 seconds per minute) to prolong starter life. Extended crank- ing can damage the starter motor.

6.After the engine starts, allow it to warm-up for a few seconds before moving the choke. Move the choke inward in small steps to allow the engine to accept small changes in speed and load. Continue moving the choke in until it is fully off and the engine is run- ning smoothly.

7.Place the throttle at the maximum setting.

8.Position each tool circuit switch to 10 GPM. The tool can now be used.

9.Reverse the above procedure to stop using the tool.

COLD WEATHER STARTUP

1. Use the procedures below for starting the engine

and using the tool circuits or driving the TracHorse in cold weather.

2.Hydraulic fluids are thicker in cold weather. There- fore, it is recommended that the engine be run at low idle long enough to bring the hydraulic fluid tem- perature up to a minimum of 50 °F/10 °C.

3.If the tools and tool hoses are cold, it is recommend- ed to allow hydraulic fluid to circulate through the tool hoses until warm before using the tools.

SHUTDOWN

1.Ensure each flow selector switch is in the OFF posi- tion.

2.Move the throttle control to idle.

3.Allow the engine to idle for approximately one min- ute and move the Ignition Switch to the OFF posi- tion.

NOTICE

If the engine runs out of gas or dies during operation

and the ignition switch is left in the ON or RUN position, this could drain the battery. Make sure the ignition switch is returned to the OFF position.

14 ► MHP3 User Manual

Page 13 Page 15
Image 14
Page 13 Page 15
Contents TracHorse Page Table of Contents Safety Symbols Local Safety RegulationsSafety Precautions Do not Operate the Trachorse in ENSafety Precautions Tool Stickers & Tags Hose Safety Tags Hose TypesHose Recommendations Tool to Hydraulic Circuit Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsHose & Fitting Connections Inch ID HOSE, 25 FT to 50 FT LongPRE Operation Procedures OperationQuick Disconnect Couplers Operating the Tool CircuitDual Circuit Combined for 10 GPM Cold Weather StartupShutdown Slope Operation Forward TravelReverse Travel Traveling Forward or ReverseForward Travel Loading and Unloading Turning From a StopHydraulic System Maintenance Routine MaintenanceEngine Maintenance LiftingRemoving Condensed Moisture from Hydraulic Fluid Adjusting Track TensionFilling the Reservoir Checking Suction HoseTroubleshooting Problem Cause SolutionFuel Tank MIX OLD Style Tank and CAP with NEW Style Tank and CAPFilters SpecificationsAccessories Adjusting Track Tension MHP3 Parts List MHP3 Parts LIST-MAJOR Assembly QTY DescriptionMHP3 Parts Illustration Hose & Fitting Illustration MHP3 Parts List MHP3 Parts LIST-HOSE & Fitting MHP3 Parts Illustration MHP3 Electric Wiring Schematic Coupler SET GTR20H12 MHP3 Honda Engine Illustration 22 MHP3 PartsMHP3 Parts List MHP3 Honda Engine Parts List
Related manuals
Manual 34 pages 1.96 Kb

MHP3 specifications

Stanley Black & Decker has long been a leader in the tools and hardware industry, and their MHP3 model exemplifies the brand's commitment to innovation and quality. The MHP3 is a multi-use power tool, expertly designed to meet the rigorous demands of both professionals and DIY enthusiasts alike.

One of the standout features of the MHP3 is its powerful motor, delivering robust performance for a variety of tasks. With variable speed control, users can easily adjust the tool's power to suit specific applications, ensuring optimal results whether drilling, fastened, or cutting. The ergonomic design of the MHP3 ensures a comfortable grip, reducing fatigue during prolonged use.

The MHP3 incorporates advanced cordless technology, which adds a layer of convenience and mobility for users. Powered by a high-capacity lithium-ion battery, it offers extended run times and can be charged quickly, allowing for minimal downtime on jobs. The battery life indicator is a thoughtful addition, helping users monitor remaining power and plan their tasks accordingly.

Another remarkable characteristic of the MHP3 is its versatility. It comes with interchangeable attachments, allowing users to tackle a multitude of projects without needing multiple tools. This adaptability makes it a favorite among professionals who require a reliable tool that can efficiently manage different jobs on-site. The tool's compatibility with a wide array of accessories further enhances its functionality.

Safety features are paramount in tool design, and Stanley Black & Decker has ensured that the MHP3 is equipped with several. The integrated safety switch prevents accidental startups, while the durable outer casing protects internal components from damage during rigorous use.

In addition to its functional capabilities, the MHP3 is also designed with aesthetics in mind. With a modern and sleek profile, it fits well in any tool collection while being practical for everyday use.

Overall, the Stanley Black & Decker MHP3 stands out as a comprehensive power tool solution. Its combination of power, versatility, and safety features makes it an indispensable addition to any workshop or job site, embodying the brand's commitment to delivering quality tools that meet the needs of consumers across various sectors. Whether you're a seasoned professional or just starting on home improvement projects, the MHP3 is engineered to deliver outstanding performance and reliability.
Top Page Image Contents