Alesis ADAT-XT manual Footswitch Controls, Footswitch Controlled Punching

Page 57

Basic Operations: Chapter 4

FOOTSWITCH CONTROLS

The XT provides two footswitch jacks: [LOCATE/PLAY/LRC REMOTE] and [PUNCH IN/OUT] . Both accept any momentary, single pole/single throw, 1/4-inch mono (T/S) footswitch. During power-up, the XT checks the footswitch to determine whether it is normally open or normally closed type, and calibrates itself accordingly. If you use a footswitch and its operation seems “reversed,” make sure it is firmly plugged into the jack, then turn off the XT, wait a few seconds, and turn the XT on again. It will calibrate itself to work with the footswitch.

Either the [PUNCH IN/OUT] or [LOCATE/PLAY/LRC REMOTE] jack can also be used for connecting an LRC Remote Control. The PUNCH footswitch and the LRC cannot be used at the same time, since they occupy the same jack, unless you connect them with a Y-cord. However, you can interchange them if you observe certain precautions (see next section).

FOOTSWITCH CONTROLLED PUNCHING

The [PUNCH IN/OUT] footswitch is used to enable and disable recording.

If a track (or tracks) is record-enabled, and the tape is playing, pressing the punch footswitch puts the track(s) into record mode at the instant you punch. This is equivalent to pressing [PLAY] and [RECORD] to enter record mode.

If the XT is already in record mode, pressing the footswitch punches out of record (the track(s) will remain record-enabled should you need to punch in again later on) and the tape will continue to play. This is equivalent to pressing [PLAY].

FOOTSWITCH CONTROLLED AUTOLOCATING

The [LOCATE/PLAY] footswitch has three functions:

If the transport is currently stopped, pressing the Locate/Play footswitch is the equivalent to pressing the [PLAY] button.

If the transport is currently playing or recording, pressing the Locate/Play footswitch causes the transport to punch out of record, fast wind to the Locate 1 point (this may be entered by pressing [SET LOCATE] followed by the [LOCATE 1] button; see page 47), and then either Stop or Play, depending on the setting of the Auto-Play function.

If the XT is in the process of locating, pressing the Locate/Play footswitch will stop the transport.

ADAT XT Reference Manual

53

Image 57
Contents Alesis ADAT-XT Introduction Adat XT Reference Manual Conventions Adat XT Reference Manual Contents Basic Operations Analog Recording Basics Digital Recording Basics Why S-VHS? Index Maintenance/Service Cleaning Obtaining Repair Service AC Power Hookup Setting UPUnpacking and Inspection ChapterSetting Up Line Conditioners and Protectors About Audio CablesInput Normaling Basic Audio HookupWord on ADAT’S S-VHS Cassette Tape Threaded VS. UnthreadedThermal Considerations in Rack Mounting Operating EnvironmentMounting on a Shelf or NON-RACK Enclosure Avoiding Electromagnetic InterferenceYour First Session POWER-UP,AND Tape InsertionABS 0H 15M 48S ABS n0 F0Sample Rate Selection Formatting a Tape a MustFormatting a NEW Tape Recording While FormattingTo record-enable a track Track Selection and Setting LevelsREL 0H 01M 29S Making a RecordingRecording Transport ButtonsTo make a recording Record LED turns off, while the Play LED remains litTo engage Cue mode To engage Review modePlayback Reviewing and CueingLocating REL 0H 00M 00SPage To loop a section of tape Creating a LoopRehearsing Automated RecordingTo automatically punch in and out Measure twice or more, and cut only onceABS 00 % 00 C Track Delay70 mS Pitch ControlTrack Copy To adjust the display brightnessDisplay Brightness To bounce audio from one track to anotherConnections Input Jack CharacteristicsAnalog Audio Unbalanced Inputs Analog Audio Unbalanced OutputsAdditional grounds Analog Audio Balanced Inputs and OutputsInput Mode Analog Audio Input ModeTo synchronize multiple XTs and/or ADATs Sync IN/OUTTo connect the digital optical network Digital Audio IN/OUTRehearse and Auto Record features FootswitchesXT Remote VersaTape Formatting Basic OperationsFormatting Considerations Complete FormatBe sure the tape is completely rewound Format ExtendABS Pr 0t 0 n ABS Pr 0t 0 FFWrite Protect Override To extend the format on a partially formatted tapeReading the Display Display Icons Basic Operations Time Counter & ABS/REL Button 01M 29SLocate SelectedEdit Value Button Basic EditingEntering Numeric Values Editing Individual DigitsAnalog Input Input SelectDigital Input Track CopyBasic Operations Input Monitor Auto Input MonitorALL Input Monitor Fine Meter Mode Peak Mode ButtonMeters Recording a Benchmark T APESetting Levels Record EnableEject Transport ControlsRewind /REVIEW Fast Forward /CUEStop RECORD/PUNCH in or OUTWhether the tape being played is formatted or not To start recordingRecord Crossfade Time Sample Rate ClockPositions as before To select the sample rateFA dE 2 Displaying Frames VS THS/SECONDSTo set the Crossfade Time About Pitch Changing To set the Track Delay amount To turn Track Delay on and offTo set multiple tracks to the same Track Delay value 10 mSAutolocation Controls Absolute ABS Time VS . Relative TimeLocate Locating Setting Locate PointsTo store a Locate Point memory on the fly To edit a Locate Point memoryAuto Return Auto LoopingAuto Play Loop LimitTape Length Auto RecordLooped Recording RehearsalTo set the tape length European equivalents and approximate recording timesErroneously selected, to avoid damage to the tape Footswitch Controls Footswitch Controlled PunchingFootswitch Controlled Autolocating Using the XT Remote Operation OverviewSynchronizing Machines Achieving Lock Master /SLAVE InteractionMaster Format ENABLED, Complete Format Independent Slave ModeMaster Format ENABLED, Format Extend Formatting Multiple TapesMaster Format Disabled Master Format DISABLED, Format ExtendBefore punching into format record Recording Digital Audio Making Digital BackupsBouncing Tracks Between Adats Reassigning Channels to Different TracksRecording Digital Audio from Other Sources To make a backup tapeDigital Clock Considerations Tape OffsetABS 0H 00M 00S Setting the Machine OffsetXT Transport Speed Combining XTS and AdatsSample Rate VS. Pitch Control Input MonitoringHere are some possible solutions Polarity DifferencesConnections Multiple ADAT-XT Operation Chapter Multiple ADAT-XT Operation Adat XT Reference Manual Combined MULTITRACK/MASTERING Deck ApplicationsLIVE/LONG-TERM Recording Locking to Video Code only Master Midi Machine Control Virtual Remote ControlComputer Control Midi Systems Virtual TrackingModular Recording Libraries and ArchivesCalculating Tape Offset Using the Locates Using Track Copy AS a Digital RouterPress Edit VALUE, then press Locate Analog Recording Basics Digital Recording ConceptsDigital Recording Basics Appendix aWHY S-VHS? TROUBLE-SHOOTING Index TroubleshootingRE-INITIALIZING Appendix BAbout Error Rate Readings Error Rate DisplayABS d1 SP E rr ABS d1 SP r E9Adat Head Maintenance MAINTENANCE/SERVICE Tape Maintenance Safe TapeCleaning Drum Time DisplayObtaining Repair Service MaintenanceRefer ALL Servicing to Alesis Customers in the USAAppendix B Troubleshooting Appendix C Error CodesAutomatic Brake Calibration Procedure Specifications Steps to Take Before Calling for HelpAppendix D Audio Digital Inputs/Outputs Or Analog-to-Digital Converter GlossaryDAT BusMMC MidiSMPTE/LTC OutputVitc VHSIndex Index Adat XT Reference Manual