Alesis ADAT-XT manual Specifications, Steps to Take Before Calling for Help, Appendix D

Page 87

Appendix D: Specifications

2.Turn off the POWER switch. Hold REWIND and FAST FORWARD while turning the power back on again. The display will read "CALIbrAt".

3.Insert the tape into the transport.

4.At this time the unit will adjust the brake tension automatically. The transport will shuttle back and forth for about 5 minutes. During the operation, the tape will half-eject twice. This is normal.

5.The display should briefly read "PaSS" before ejecting the tape fully and returning to the "ADAT-XT" start-up screen. The brakes have now been recalibrated.

If the "CAL brAc" message appears again shortly after a brake calibration has been performed, there may be something wrong with the tape being used. Check operation with another tape. If the message persists, the unit must be professionally serviced.

Note: If these errors occur only with a certain tape, or display once in a while, it’s probably not cause for concern. Errors 1 through 3 and 9 can indicate conditions that may damage a tape; the other errors won’t damage the tape or the machine. Backup the data from that tape to another machine, if possible, and continue working from the backup copy.

STEPS TO TAKE BEFORE CALLING FOR HELP

If an error message is displayed or if an ADAT starts behaving strangely, then please follow the suggested steps below:

1Stop the tape playing (or recording). Does the error go away?

2Rewind the tape a minute or two. Press [PLAY]. Does the error recur?

3Eject the tape. Place it back in the XT and press [PLAY]. Does the error recur?

4Turn down the volume of any mixer or amplifier you have connected to the outputs of the XT. Turn the power of the XT off, wait a minute and then re-power the XT. Repeat steps 1 to 3. Does the error come back?

5If it does, then try a different tape. Repeat steps 1 to 3. Does the problem recur?

6Try the tape in a different XT or ADAT. (If you are using a single ADAT system, see if you can visit your dealer.) It does not make sense to send your XT in for service when there may be only a problem with, for example, some tapes that you are using. If the same problems occur in another XT or ADAT, then either the tape is faulty or it was formatted on an out of alignment XT or ADAT. At this point, you should call Alesis Product Support. If the problem does not occur, and the tape works fine, then we need to look at your XT. You need to call Alesis Product Support.

Whatever happens, the answers to all these questions are useful information for our Product Support representatives. The more we know, the faster we can discover the cause of your problems. You will help us isolate whether the problem lies in the XT, the tape or somewhere else.

APPENDIX D

SPECIFICATIONS

Transport

Recording Format:

ADAT Rotary head digital recording

Tape Format:

S-VHS cartridge

ADAT XT Reference Manual

83

Image 87
Contents Alesis ADAT-XT Introduction Adat XT Reference Manual Conventions Adat XT Reference Manual Contents Basic Operations Analog Recording Basics Digital Recording Basics Why S-VHS? Index Maintenance/Service Cleaning Obtaining Repair Service Chapter Setting UPAC Power Hookup Unpacking and InspectionSetting Up Line Conditioners and Protectors About Audio CablesInput Normaling Basic Audio HookupWord on ADAT’S S-VHS Cassette Tape Threaded VS. UnthreadedAvoiding Electromagnetic Interference Operating EnvironmentThermal Considerations in Rack Mounting Mounting on a Shelf or NON-RACK EnclosureABS n0 F0 POWER-UP,AND Tape InsertionYour First Session ABS 0H 15M 48SRecording While Formatting Formatting a Tape a MustSample Rate Selection Formatting a NEW TapeMaking a Recording Track Selection and Setting LevelsTo record-enable a track REL 0H 01M 29SRecord LED turns off, while the Play LED remains lit Transport ButtonsRecording To make a recordingReviewing and Cueing To engage Review modeTo engage Cue mode PlaybackLocating REL 0H 00M 00SPage To loop a section of tape Creating a LoopMeasure twice or more, and cut only once Automated RecordingRehearsing To automatically punch in and outPitch Control Track DelayABS 00 % 00 C 70 mSTo bounce audio from one track to another To adjust the display brightnessTrack Copy Display BrightnessAnalog Audio Unbalanced Outputs Input Jack CharacteristicsConnections Analog Audio Unbalanced InputsAdditional grounds Analog Audio Balanced Inputs and OutputsInput Mode Analog Audio Input ModeTo synchronize multiple XTs and/or ADATs Sync IN/OUTTo connect the digital optical network Digital Audio IN/OUTVersa FootswitchesRehearse and Auto Record features XT RemoteComplete Format Basic OperationsTape Formatting Formatting ConsiderationsBe sure the tape is completely rewound Format ExtendTo extend the format on a partially formatted tape ABS Pr 0t 0 FFABS Pr 0t 0 n Write Protect OverrideReading the Display Display Icons Basic Operations Selected 01M 29STime Counter & ABS/REL Button LocateEditing Individual Digits Basic EditingEdit Value Button Entering Numeric ValuesTrack Copy Input SelectAnalog Input Digital InputBasic Operations Input Monitor Auto Input MonitorALL Input Monitor Recording a Benchmark T APE Peak Mode ButtonFine Meter Mode MetersSetting Levels Record EnableFast Forward /CUE Transport ControlsEject Rewind /REVIEWTo start recording RECORD/PUNCH in or OUTStop Whether the tape being played is formatted or notTo select the sample rate Sample Rate ClockRecord Crossfade Time Positions as beforeFA dE 2 Displaying Frames VS THS/SECONDSTo set the Crossfade Time About Pitch Changing 10 mS To turn Track Delay on and offTo set the Track Delay amount To set multiple tracks to the same Track Delay valueAutolocation Controls Absolute ABS Time VS . Relative TimeLocate To edit a Locate Point memory Setting Locate PointsLocating To store a Locate Point memory on the flyLoop Limit Auto LoopingAuto Return Auto PlayRehearsal Auto RecordTape Length Looped RecordingTo set the tape length European equivalents and approximate recording timesErroneously selected, to avoid damage to the tape Footswitch Controls Footswitch Controlled PunchingFootswitch Controlled Autolocating Using the XT Remote Operation OverviewSynchronizing Machines Achieving Lock Master /SLAVE InteractionFormatting Multiple Tapes Independent Slave ModeMaster Format ENABLED, Complete Format Master Format ENABLED, Format ExtendMaster Format Disabled Master Format DISABLED, Format ExtendBefore punching into format record Reassigning Channels to Different Tracks Making Digital BackupsRecording Digital Audio Bouncing Tracks Between AdatsRecording Digital Audio from Other Sources To make a backup tapeDigital Clock Considerations Tape OffsetABS 0H 00M 00S Setting the Machine OffsetInput Monitoring Combining XTS and AdatsXT Transport Speed Sample Rate VS. Pitch ControlHere are some possible solutions Polarity DifferencesConnections Multiple ADAT-XT Operation Chapter Multiple ADAT-XT Operation Adat XT Reference Manual Combined MULTITRACK/MASTERING Deck ApplicationsLIVE/LONG-TERM Recording Midi Systems Virtual Tracking Midi Machine Control Virtual Remote ControlLocking to Video Code only Master Computer ControlModular Recording Libraries and ArchivesCalculating Tape Offset Using the Locates Using Track Copy AS a Digital RouterPress Edit VALUE, then press Locate Appendix a Digital Recording ConceptsAnalog Recording Basics Digital Recording BasicsWHY S-VHS? Appendix B TroubleshootingTROUBLE-SHOOTING Index RE-INITIALIZINGABS d1 SP r E9 Error Rate DisplayAbout Error Rate Readings ABS d1 SP E rrAdat Head Maintenance Drum Time Display Tape Maintenance Safe TapeMAINTENANCE/SERVICE CleaningCustomers in the USA MaintenanceObtaining Repair Service Refer ALL Servicing to AlesisAppendix B Troubleshooting Appendix C Error CodesAutomatic Brake Calibration Procedure Specifications Steps to Take Before Calling for HelpAppendix D Audio Digital Inputs/Outputs Or Analog-to-Digital Converter GlossaryDAT BusMMC MidiSMPTE/LTC OutputVitc VHSIndex Index Adat XT Reference Manual