Marmitek 20068 / 300704 Setting the infrared return channel for using Remote control

Page 7

5.Turn on the TV and find the channel that you have set. Your TV’s operating instructions will tell you how to do this. You will now see the test pattern on the set channel. Now check that there is no interference on the neighbouring TV channels. If there is, you should select another two (or if possible) three free channels and set the modulator to these channels.

After you have done this set the 8th dip switch (test pattern) back to OFF. From now on you will be able to watch the attached A/V appliance on the channel that you have set.

6.Now turn on the required A/V appliance (DVD, video recorder, satellite receiver, PC, camera, etc.). You can now view the signal on the TV. If you have a number of TVs connected to the same aerial network then you can also view this signal on the other TVs. To do so you will first have to set the correct channel on each TV.

7.Setting the infrared return channel for using

remote control

An infrared receiver is supplied with the set. This receiver can be fitted between the TV and the aerial signal. The receiver converts the infrared signal from your remote control and sends this signal back to the modulator through the aerial cable.

Using the supplied infrared eye you can convert this back to an infrared signal and send it to the connected appliance. In this way you can operate the connected appliance (e.g. a DVD player) from another room.

It is easier to connect this if someone helps you.

1.Disconnect the aerial cable connected to the back of your TV. Connect this to the ‘ANT IN’ / ‘In’ connection on the metal part of your infrared receiver.

2.Reconnect the ‘TV OUT’ / ‘To TV’ side to your TV. You can use the supplied adaptors for this (F connector to IEC).

3.Position the red plastic part containing the infrared receiver where it can be seen from where you want to use your remote control. Avoid direct sunlight or light from a plasma screen.

4.Connect one of the two supplied transformers to the metal part of the IR receiver.

5.Turn the switch on the side of the red plastic part to the ON position.

6.Connect the supplied infrared eye to the side of the modulator, where it is marked ‘IR OUT’. The infrared eye has a self-adhesive backing. Remove the protective sheet and stick the eye carefully over the infrared sensor on your video recorder, DVD player or satellite receiver. This infrared sensor can usually be recognised by the dark coloured plastic window.

MEGAVIDEO55tm

7

Image 7
Contents AVIDEOMEGAVIDEO5555 Entrée antenne AntennaAntenne ingang Use and operation of the MegaVideo Safety precautionsConnecting appliances to the MegaVideo 55 modulator Contents of MegaVideo 55 SetYou are using F plugs Connecting the aerial signal to the MegaVideo 55 modulatorUsing a suitable A/V switcher Using a trio RCA splitterYour connecting cables have not yet been fitted with plugs Setting the channelSetting the infrared return channel for using Remote control Operating more than one appliance Using infrared receivers in a number of roomsTechnical details Problems and solutionsMarmitek Anwendung und Betriebsweise des MegaVideo SicherheitshinweiseMit Hilfe eines Scart-Kabels Zusammensetzung MegaVideo 55 SatzDas Anschließen von Geräten an den MegaVideo 55 Modulator Mit Hilfe eines Cinch-KabelsMit Hilfe eines geeigneten A/V-Schalters Mehrere Geräte anschließen?Mit Hilfe von drei Cinch-Verteilern Sie verwenden F-Stecker Das Einstellen des KanalsSie verwenden IEC-Stecker MEGAVIDEO55tm Die Benutzung von Infrarot-Empfängern in mehreren Räumen Mehrere Gerät ansteuern Technische Daten Application et fonctionnement du MegaVideo Consignes de sécuritéConnexion des appareils au modulateur MegaVideo Composantes de linstallation MegaVideoAu moyen dun câble RCA Au moyen dun commutateur A/V approprié Connexion du signal dantenne au modulateur MegaVideoAu moyen dun câble péritel Connexion de plusieurs appareils ?Vous avez recours à des prises F Sélection de la chaîneVous avez recours à des prises IEC MEGAVIDEO55tm Récepteur Infrarouge Commander plus dun appareil à la fois Problèmes et solutionsUtiliser des récepteurs infrarouges dans plusieurs pièces Données techniques Toepassing en werking MegaVideo VeiligheidswaarschuwingenDoor middel van een scartkabel Samenstelling MegaVideo 55 setAansluiten van apparatuur op de MegaVideo 55 modulator Door middel van een tulpkabelDoor middel van een geschikte A/V schakelaar Meerdere apparaten aansluiten?Door middel van een drietal tulpsplitters Uw verbindingskabels zijn nog niet voorzien van pluggen Instellen van het kanaalMaakt gebruik van F-pluggen Maakt gebruik van IEC-pluggenMEGAVIDEO55tm Infrarood ontvangers gebruiken in meerdere kamers Technische gegevens Problemen en oplossingenMeer dan één apparaat aansturen Channel Frequency MHz switch settings Channel Frequency MHz switch settings