Multiquip manual MT-84F Operation, Rammer Gearbox and Spring Cylinder Oil Bath, Fuel Check

Page 16

This section is intended to assist the operator with the initial start-up of the MT-84F Tamping Rammer. It extremely important that this section be read carefully before attempting to operate the rammer.

DO NOT use your rammer until this section is thoroughly understood.

CAUTION

Failure to understand the operation of the MT-84F Tamping Rammer could result in severe damage to the trowel or personal injury.

Rammer Gearbox and Spring Cylinder Oil Bath

This unit uses an oil bath lubrication system.Perform the following:

1.Check the oil level through the oil level sight glass (Figure 4) at the rear of the tamper foot.

Figure 4. Foot Housing Sight Glass

2.If oil is not visible, add 10W-30 motor oil into the oil fill plug opening (Figure 2). The bath contains approximately 1.7 pints (800 cc.)

The oil bath level should be kept

NOTEat the half way point of the sight glass.

it often.

MT-84F — OPERATION

Fuel Check

1.Check the fuel level in the fuel tank.If the fuel level is low, fill the fuel tank (Figure 5) with clean unleaded gasoline.

Figure 5. Fuel Tank

Engine Oil Check

1.To check the engine oil level, place the rammer on secure level ground with the engine stopped.

2.Remove the filler dipstick from the engine oil filler hole (Figure 6) and wipe it clean.

Figure 6. Engine Oil Dipstick

3.Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

4.If the engine oil level is low, fill to the edge of the oil filler hole with the recommended oil type (Table 3). See Table 2 for the oil capacity of your type engine.

Table 3 Motor Oil Grade

Season or Temperature

Grade of motor oil

(higher than MS class)

 

 

 

 

Spring, Summer or Autumn

SAE 30

+120° F to +15° F

 

 

 

 

Winter

 

SAE 30

+40° F to +15°

F

 

 

 

 

Below +15° F

 

SAE 10W-30

 

 

 

PAGE 16 — MT-84F — OPERATION & PARTS MANUAL — REV. #2 (06/30/05)

Image 16
Contents Model MT-84F MT-84F Proposition 65 Warning MT-84F Operation & Parts Manual REV. #2 06/30/05 MT-84F Table of Contents MT-84F Parts Ordering Procedures When ordering parts Please supply the following informationMT-84F Safety Message Alert Symbols MT-84F Safety Message Alert Symbols Rotating Parts HazardsMT-84F Rules for Safe Operation MT-84F Rules for Safe Operation Machine Safety Decals Rammer Operation and Safety DecalsMT-84F Operation and Safety Decals MT-84F General Information Definition of Tamping RammerConstruction of Tamping Rammer Rammer Gearbox and Spring CylinderMT-84F Specifications MT-84F Controls and Components MT-84F Basic Engine Robin EH-12-2D Engine Controls and ComponentsRammer Gearbox and Spring Cylinder Oil Bath MT-84F OperationFuel Check Inspection Initial Start-upOperation Stopping The Engine200 300 Hours Pre-Cleaner MaintenanceLong Term Storage MT-84F -TROUBLESHOOTING Guide MT-84F -TROUBLESHOOTING Guide NO. Column Part NO. ColumnQTY. Column Remarks ColumnMT-84F- Suggested Spare Parts MT-84F Rammer 1TO 3 UnitsMT-84F- Nameplate and Decals Part Name QTY Remarks MT-84F Crankcase and Engine Assy Part Name 28 MT-84F Operation & Parts Manual REV. #2 06/30/05 MT-84F Crankcase and Engine Assy MT-84F Guide Cylinder and Foot Assy Piston PIN MT-84F -TANK and Handle Assy Tank CAP ASSY., OR,DB Robin EH-12-2D Engine Crankcase and Cylinder Assy Robin EH-12-2D Engine Crankcase and Cylinder Assy Robin EH-12-2D Engine Crankshaft and Piston Assy Crankshaft CP Robin EH-12-2D ENGINE-MUFFLER, AIR CLEANER, CAM& CARB. Assy Robin EH-12-2D Engine -MUFFLER, AIR CLEANER, CAM& CARB. Assy Robin EH-12-2D Engine -GOVERNOR Assy Governor Lever CP Robin EH-12-2D Engine -RECOIL Starter and Blower Assy Robin EH-12-2D Engine -RECOIL Starter and Blower Assy Robin EH-12-2D Engine Magneto Assy Flywheel CP Robin EH-12-2D Engine Carburetor Assy Throttle Valve Effective October 1, 2002 Terms and Conditions of Sale Parts MT-84F Operation & Parts Manual REV. #2 06/30/05 Heres HOW to GET Help