STEP 4 - Attach Flavor Activator Pins, Grease Cup Hanger, Burner & Heat Shield
Follow the steps in order below. Refer to the step numbers below and beside the images.
1.Assemble 2 flavor activator Mounting Studs and two Fiber Washers to the bowl using 2 M6 nuts.
2.Insert Grease Cup Hanger into bowl.
3.Insert Burner Venturi tubes down through holes in bottom of grill bowl toward front of grill. Also insert igniter wire through hole in bottom of bowl. From underside of bowl, insert 2 ST 4.0 x 10mm screws into burner mounting holes and tighten.
4.Thread grease cup holder through center hole of heat shield and secure heat shield to bottom of bowl as shown using 1 ST 4.0 x 10mm Screw. The shield will later be secured to the cylinder slide bracket on the cart.
|
|
|
|
|
| Mounting |
|
| Grease Cup Hanger |
|
|
| |||||
|
|
|
|
| 2 |
| |||||||||||
|
|
|
|
|
| Stud |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| M6 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| 4 |
|
|
|
|
|
|
| |||||
|
|
|
|
|
| 2 pcs |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Fiber |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Washer |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 2 pcs |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Nut |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| M6 |
|
|
|
|
|
|
|
|
| 3 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
| 2 pcs |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Screw
ST 4.0 x 10mm 3 pcs
Inside of Bowl
1
Note orientation of venturi tubes to Heat Shield.
Install Heat Shield toward left side (tank side) of Body.
7