PGS S27R, S36R owner manual INFRA-BROIL Rear Burner, Side Burner KIT

NON-COMBUSTIBLE MATERIAL AND MUST BE AT LEAST 30” AWAY FROM ANY COMBUSTIBLE MATERIAL.

Masonry Cutouts

Model	Height	Depth	Width
Newport	9 ½”	23”	28”
Newport Gourmet	9 ½”	23”	28”
Pacifica	9 ½”	23”	36 ½”
Pacifica Gourmet	9 ½”	23”	36 ½”
Side Burner Kit	9”	18 ½”	12 ½”
MDS (door kit)	16 ¾”		27 ½”

INFRA-BROIL REAR BURNER

The PGS Infra-Broil Kit comes as a standard feature on our models Newport Gourmet and Pacifica Gourmet. The Infra-Broil is a rear burner especially designed for those back yard chefs who love to rotisserie. It features 12,000 BTU of radiant heat for extremely efficient roistering. It will cook poultry and beef quickly and efficiently to perfection every time!

Please note, when using the Infra-Broil Burner, you should never have any of the lower burners on. Using any other lower burner at the same time as a rear burner poses potential problem with insufficient oxygen, which could cause rear burner to go out and cause a gas leak.

To operate, turn far right hand knob with the word “ROTIS” under it to the “HI” position. Push Sure Start Ignition button. Burner should light within five seconds.

IF THE BURNER FAILS TO LIGHT, IMMEDIATELY TURN CONTROL OFF TO PREVENT GAS BUILD-UP. WAIT FIVE MINUTES FOR GAS TO CLEAR AND TRY THE ABOVE PROCEDURE AGAIN. IF THE BURNER DOES NOT LIGHT WITH THE ELECTRONIC IGNITION, LIGHT THE BURNER WITH A MATCH OR OTHER HAND HELD IGNITOR. TOUCH LIGHTED MATCH OR HAND HELD IGNITOR TO THE LOWER RIGHT HAND SIDE OF THE “INFRA-BROIL”.

Manual Lighting of Infra-Broil Rear Burner

Rotisserie motor mount should be installed on the left hand side of the Hood Support Brackets.

Please use care when operating electric rotisserie motor and be certain that outlet used is grounded and incorporates a Ground Fault Interrupter. When operating, be sure to keep cord away from all liquids and hot surfaces.

When using Infra-Broil back burner, we suggest that you remove the cooking grid and place a metal pan directly on the rock. We suggest that you fill pan a minimum of one quarter full with liquid and that you regularly check pan to ensure liquid remains during the entire rotisserie cooking.

A counter balance is included with your PGS rotisserie kit, we suggest positioning it so that it is opposite of your meat, to balance the load on your motor.

SIDE BURNER KIT

A great optional accessory to compliment your PGS Legacy grill is our high output “Infra-Red” Side Burner Kit. This will allow you to keep all the mess and heat outside when grilling. You can boil water for corn on the cob, lightly sauté creams or vegetables, simmer sauces for basting your meal or any other task that you could do on your range in the kitchen.

Side Burner Kit for the portable cart is attached to the RIGHT HAND SIDE on your portable cart with (4) four screws included in the cart shelf bracket kit. Two people are needed to accomplish this.

Remove packaging. Have one person hold the side burner in place while the other starts all four screws. When all four screws are started, tighten all. As an alternative, you may wish to attach the side burner kit prior to placing grill head in cart. Simply lay cart down on a padded surface on its’ left hand side. Side burner can now be mounted on right hand side of cart with four screws included to attach side shelf kit. PLEASE NOTE, SCREWS FOR SIDE

BURNER SHOULD NOT BE TIGHTENED UNTIL AFTER GRILL HEAD IS PLACED ON CART. BATTERY IS PLACED WITH “+” FACING OUT.

If Natural Gas, attach a flexible gas feed line to 3/8” male flare fitting found on the underside of the side burner kit. Tighten fitting. Feed balance of flexible gas feed line through hole in side of cart. Remove brass accessory cap that is part of the natural gas regular, and screw feed line to this assembly. See picture below:

Natural Gas Connection between Flex Connector

and Regulator Assembly

If LP, feed long section on 2 way hose and regulator combo through hole in right hand side wall of cart. Connect Brass fitting to 3/8” male flare fitting found on the underside of the side burner kit.

Tighten fitting. Attach short section of hose coming off regulator to gas grill supply. Connect regulator to LP tank

15