Lighting the side burner
IMPORTANT: Light only one burner at a time.
Do not lean over burners. Push in and turn to “LITE” the control knob for the burner you wish to use.
front
rearburner burner
You will hear the “snapping” sound of the spark. Once burner is lit, turn knob from the “LITE” position to the desired setting. Repeat for the other burner as needed.
IMPORTANT: If burner does not light immediately, turn the burner knob to “OFF” and wait 5 minutes before relighting.
Manually lighting the burners
1.Strike a match to light it.
2.Carefully guide the lit match to the burner you wish to light.
3.Push in and turn the burner knob to “LITE” for the burner closest to the lit match. The burner will light immediately.
4.Repeat steps 1 through 3 for each burner.
IMPORTANT: If burner does not light immediately, turn the burner knob to “OFF” and wait 5 minutes before relighting.
If any burners do not light after attempting to manually light them, contact the KitchenAid Assistance Center (see “Requesting Assistance or Service” section).
Replacing the Igniter battery
If igniters stop sparking, the battery should be replaced.
1.Lift up at bottom of battery tray and slide battery tray out.
2. Remove battery and replace with alkaline
3. Slide battery tray back
into compartment. lift up and slide out tray
Cleaning
General Tips
IMPORTANT: Before cleaning, make sure all controls are off and the burners are cool. Always follow label instructions on cleaning products.
For routine cleaning, wash with soap and water using a soft cloth or sponge. Rinse with clean water and dry at once with a soft,
Never use steel wool to clean the side burner, as it will scratch the surface.
Stainless Steel
IMPORTANT: Do not use
Cleaners should not contain chlorine. Damage may occur to the product finish.
Rub in direction of grain to avoid scratching or damaging the surface.
Food spills should be cleaned as soon as entire Side Burner is cool. Spills may cause permanent discoloration.
•Use Stainless Steel Cleaner & Polish (Part #4396095). See “Requesting Assistance or Service” section to order.
•Use a mild liquid detergent or all- purpose cleaner according to label instructions.
•Rinse with clean water and dry at once with soft,
•Use vinegar to remove hard water spots. Rinse with water and dry thoroughly.
•Use a glass cleaner to remove fingerprints.
IMPORTANT: Make sure gas supply is off and all control knobs are in the “OFF” position. Make sure the Side Burner is cool.
Exterior
The quality of this material resists most stains and pitting, providing that the surface is kept clean and protected.
•Apply stainless steel polish to all non- cooking areas before first use.
•Cleaning should always be followed by rinsing with clean warm water.
•Wipe the surface completely dry with a soft cloth.
•For tough spots or
Interior
•Cleaning should always be followed by rinsing with clean, warm water.
•Use a mild liquid detergent or all- purpose cleaner, following label instructions. Rinse with clean water and dry completely with a soft,
•A
•For small,
Burner caps and grate
•Clean with a brass bristle brush.
•Wash grate using mild detergent, warm water and degreaser.
•Rinse with clean water and dry with soft,
•Use Stainless Steel Cleaner & Polish (Part No. 4396095). See “Requesting Assistance or Service” section to order.
Knobs, plastic and flange area around knobs
IMPORTANT: Do not use steel wool, abrasive cleaners, or oven cleaner.
Do not soak knobs.
•Wash with mild detergent, using a soft cloth and warm water. Rinse and dry.
Control panel graphics
IMPORTANT: Do not use steel wool, abrasive cleaners or oven cleaner.
Do not spray cleaner directly onto panel.
Clean around the burner labels gently; scrubbing may remove printing.
•Wash with mild detergent, using a soft cloth and warm water. Rinse and dry.
7