Panasonic TX-86PW300A, TX-76PW300A operating instructions VCR Codes, DVD Codes

Page 31

Remote Control VCR/DVD Operation

Manufacturers’ Code Settings

This remote control has been designed to work with a variety of VCRs and DVD players. In order for this to occur, the setting for the VCR or DVD must be programmed into the Remote Control.

1.To set a VCR, slide the remote control VCR-DVD switch to VCR.

To set a DVD, slide the remote control VCR-DVD switch to DVD.

2.Push the remote control VCR-DVD Power Button and keep it Pushed.

3.Enter the Manufacturer’s two-digit code number using the remote control Number Buttons (The codes are shown below).

4.Push the STOP button .

5.Release the remote control VCR or DVD Power Button .

6.Check the operation of the VCR or DVD. If it does not operate correctly, repeat steps 1 to 5 and use an alternate code (if there is one).

VCR CODES

Manufacturer

Code

Manufacturer

Code

 

 

 

 

Panasonic /

10, 11, 12, 13

NEC

40, 41, 42, 43

National

 

ORION

45, 46

AIWA

15, 16

Philips

50

FUJITSU

20

SANYO

55, 56, 57, 58

HITACHI

25, 26, 27

SHARP

60, 61

JVC

30, 31, 32

SONY

65, 66, 67

MITSUBISHI

35, 36

TOSHIBA

70, 71

 

 

 

 

DVD CODES

ManufacturerCode

Panasonic70

NOTES:

1.If the batteries are removed from the remote control the Manufacturer’s codes are lost and must be reprogrammed.

2.The list of manufacturer’s codes is given as a guideline only. Panasonic cannot guarantee that any other manufacturer’s product will work with this remote control.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents TX-86PW300A TX-76PW300A About Panasonic Panasonic and the EnvironmentCardboard PlasticsImportant Information Contents 30 ~ Owner ID22 ~ 25 ~Getting Started Connect the Aerial Connect the Power PlugTurn on the Television Insert Batteries Battery Installation and Replacement Open Battery CoverReplace Battery Cover Battery PrecautionsControl Panel Buttons Remote Control ButtonsTV / AV STR Television Control Panel ButtonsTV / AV Remote Control Television Operation Recall Changing channels in Multi PIP modeNormalisation Programme Number UP and Down Volume Down and UPHelp Sound MuteRED Green Yellow Blue Select Exit CH SearchDirect Programme Number Selection TWO Digit Programme Number SelectionMenu demo Using The On Screen DisplaysOn Screen Help External connectionNormalisation N Picture MenuMenu Subwoofer Sound MenuDolby Virtual BassTeletext Off timer Wake up timer Ch colour set Set Up MenuVCR/GAME 3D-COMBHelpful Hint Setup menu Geomagnetic CorrectionUsing the Front Panel Using the Remote ControlSetup menu Owner ID Just Aspect controlAuto 149TV / Text Teletext OperationSUB page Numbers Down and UP FavouriteTV / Text Numbers UP and DownFull / TOP / Bottom Display CancelNumber Buttons RevealTuning Menu SYS Select Tuning Menu Auto Tuning Tuning the Television to a VCR Tuning Menu Manual TuningCanceling the Fine Tuning Tuning Menu Fine TuningTuning Menu Skip Programme Number / Skip UP Remote Control VCR/DVD OperationRewind / Review PlayDVD Codes VCR CodesAV Equipment Connecting a DVD player or Set-top Box to the AV Input Connecting Equipment to the TV Rear Panel ConnectionsConnecting S-Video Equipment to the AV Input Monitor Out Customer Information Warnings and cautions Safety FirstCleaning the Remote Control Customer Information Cleaning the TelevisionCustomer’s Record Question Why are my channels on 1,2,3,4,5? Customer Information Frequently Asked QuestionsPicture Sound Check TroubleshootingSpecifications Australia NEW Zealand
Top Page Image Contents