KitchenAid KBGS274SSS0 Using the Rotisserie, Lighting the rotisserie burner

Page 12

Using the Rotisserie

 

rotisserie

rotisserie burner

motor

fork

spit rod

To avoid product damage when not using the rotisserie, remove motor and store indoors. Remove spit rod and forks. Store out of reach of children.

Lighting the rotisserie burner

For best cooking results, do not use main grill burners when using the rotisserie.

The rotisserie system is designed to cook food from the rear using intense, searing infrared heat.

1.Remove warming shelf.

2.Mount rotisserie motor on the grill’s mounting bracket. Position it securely into support bracket slots.

3.To load the spit rod, slide one of the rotisserie forks onto the spit rod with prongs facing away from handle.

4.Push spit rod through the center of the food, then slide second rotisserie fork into position.

5.Center the food and rotisserie forks on spit rod and tighten wing nuts on the rotisserie forks. If necessary, secure loose food portions with butcher’s string only.

6.Once the food is positioned on spit rod, place pointed end of rod into rotisserie motor and lower spit rod onto supports at either side of the grill.

7.Plug single-prong plug into rotisserie motor.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

8.Plug three-prong rotisserie plug into a grounded three prong outlet.

1.Do not lean over the grill.

2.Push in the rotisserie burner knob and turn the knob to “LITE/HI”. You will hear the “snapping” sound of the spark.

3.When the rotisserie burner lights, continue to hold the knob in for another 10 seconds, then release the knob and burner will stay lit. You will hear the “snapping” sound of the spark until the knob is released.

IMPORTANT: If the rotisserie burner does not light immediately, turn the burner knob to “OFF”, wait 5 minutes before relighting.

Manually lighting rotisserie burner

1.Do not lean over the grill.

2.Remove the manual lighting extension from inside the drip tray.

3.Attach a match to the clip.

4. Strike the match to light it.

5.Gently hold the lit match close to the rotisserie burner.

6.Push in and turn the rotisserie burner control knob to “LITE/HI”. Hold this knob in for 10 seconds after the burner is lit. You will hear the “snapping” sound of the spark until after the knob is released.

IMPORTANT: If the rotisserie burner does not light immediately, turn the rotisserie burner control knob to “OFF” and wait 5 minutes

before relighting.

light

7.Remove the match and replace the manual lighting extension inside the drip tray.

12

Image 12
Contents Installation Instructions USE and Care Guide Outdoor Grill Safety Important Safety Instructions Installation Requirements Tools and PartsProduct Dimensions Location RequirementsRotisserie Insulated JacketElectrical Requirements Recommended ground methodGas Supply Requirements Built-In Outdoor GrillsBuilt-In Outdoor Grill Installation Built-In ArchitectTM Series Outdoor GrillNatural Gas Use If Converted to L.P. Gas Assemble Cooking AreaCheck and Adjust the Burners Sear burner flame characteristicsAdjusting the air shutters Low flame adjustmentUsing your Outdoor Grill Lighting the grillManually lighting main grill burners Prepare the gas supplyUsing the Rotisserie Lighting the rotisserie burnerManually lighting rotisserie burner Cooking Methods Grillingl ing Chartchart IndirectHI/OFF/HI Rotisserie Chart Rotisserie Cooking TipsTrussing Poultry for the Rotisserie Cleaning Interior Control panel graphics Shaped burnersRotisserie spit rod handle Rotisserie spit rod and forksKitchenaid GAS Grill Warranty Requesting Assistance or Service