KitchenAid KFGR271SSS, KFGR383SSS Built-In Outdoor Grills, Portable Outdoor Grill Installation

Page 8

Built-In Outdoor Grills

(non-combustible construction)

Natural Gas:

Built-in grill models are equipped for use with Natural gas. They are design-certified by CSA International for L.P. (propane or butane) gases with appropriate conversion.

Built-in models are set for natural gas use and have a pressure regulator with 1/2female pipe threads.

INSTALLATION INSTRUCTIONS

Portable Outdoor Grill Installation

Assemble Cooking Area

Portable ArchitectTM Series Outdoor Grill

WARNING

rear of grill

flexible gas connector

1/2grill

gas pipe

Excessive Weight Hazard

Use two or more people to move and install grill. Failure to do so can result in back or other injury.

1. Move grill into desired outdoor location.

2.Open the hood.

For models with side burners:

1. Remove side burner cover from the top of the carton that is

located on the grill grate. Remove bubble wrap from side burner

cover and set aside.

The supply line shall be equipped with an approved shutoff valve. This valve should be located in the same area as the grill and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the appliance.

Shutoff valve “open” position

gas supply line

To grill

L.P. gas conversion from a local L.P. gas supply:

Conversion must be made by a qualified person. A qualified natural gas technician shall provide the L.P. gas supply to the selected grill location in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54 -latest edition, and local codes.

To convert to L.P. gas, the L.P. Gas Conversion Kit No. 4396311 must be used. Follow Instructions included with kit.

L.P. gas conversion using an L.P. fuel tank:

To convert to L.P. gas, the L.P. Gas Conversion Kit No. 4396311 must be used. Follow Instructions included with kit.

An L.P. gas cylinder, not larger than 20 pounds, must be purchased separately.

2.

Open carton located on the grill grate. Remove side burner

 

grate, unwrap and set aside.

3.

Remove burners and burner caps from carton and unwrap.

4.

Install each set of burners and caps inside the side burner

cavity as shown.

notch

burner

cap

burner

alignment

 

 

tab

5.Install side burner grate and cover (with extension toward grill) as shown.

cover

extension

burner grate

6.Dispose of/recycle all packaging material.

8

Image 8
Contents Installation Instructions USE and Care Guide Outdoor Grill Safety Your safety and the safety of others are very importantImportant Safety Instructions Installation Requirements Tools and PartsProduct Dimensions Location RequirementsRotisserie If you plan to use a combustible enclosureRecommended ground method Built-In Installation DimensionsElectrical Requirements Gas Supply Requirements Portable Outdoor GrillsAssemble Cooking Area Portable Outdoor Grill InstallationBuilt-In Outdoor Grills Make gas connections For all portable outdoor grillsIf Converted to Natural Gas Natural Gas Use Built-In Outdoor Grill InstallationBuilt-In ArchitectTM Series Outdoor Grill Plug in grill light If converted to L.P. gasCheck and Adjust the Burners Low flame adjustmentSear burner flame characteristics Adjusting the air shuttersUsing your Outdoor Grill Lighting the grillManually lighting main grill burners Prepare the gas supplyUsing the Side Burner Using the RotisserieLighting the side burner Manually lighting the side burnerUsing the grill light on some models Lighting the rotisserie burnerManually lighting the rotisserie burner Before GrillingCooking Methods Direct HeatIndirect Heat Indirect CookingGrilling chart Indirect Rotisserie Cooking Tips Trussing Poultry for the RotisserieCleaning Accessories Kitchenaid GAS Grill Warranty Requesting Assistance or Service