To Turn OFF GAS, Manual Lighting Procedure

OPERATING FIREPLACE

Lighting Instructions (Cont.)

To Turn Off Gas To Appliance

Manual Lighting Procedure

Optional Hand-Held Remote Operation

OPERATING FIREPLACE
Continued
7.	Turn gas control knob counterclockwise	to “PILOT”
	(see Figure 45).
8.	Push in gas control knob all the way and hold. Immediately
	light the pilot by repeatedly depressing the piezo spark
	ignitor until a ﬂame appears. Continue to hold for about
	one (1) minute after the pilot is lit. Release gas control knob
	and it will pop back. Pilot should remain lit. If it goes out,
	repeat steps 5 through 8.

•If gas control knob does not pop up when released, stop and immediately call your service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

9.Turn on all electric power to the ﬁreplace.

10.Turn gas control knob counterclockwise to “ON”.

11.	This valve is equipped with a HI/LO feature. Set ﬁreplace
	input as desired.
12. Close lower louver panel.
		Gas Control			Variable Control Knob
		Gas Control
		Knob
	Piezo		IL
	Ignitor	O	IL	OT	O
			P	OT	IH
		F	F
					N
					LO
Figure 45 - Control Valve
		TO TURN OFF GAS
		TO APPLIANCE
1.	Open lower louver panel.

MANUAL LIGHTING

PROCEDURE

1.Remove glass door (see Removing/Replacing Glass Door, page 21).

2.Follow steps 1 through 8 under Lighting Instructions, page 23.

3.Depress gas control knob and light pilot with match.

4.	Keep gas control knob pressed in for 30 seconds after light-
	ing pilot. After 30 seconds, release gas control knob. Follow
	steps 10 through 12 under Lighting Instructions.

5.Replace glass door (see Removing/Replacing Glass Door, page 21).

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 36). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions, page 23.

After lighting, let pilot ﬂame burn for about one minute. Turn control knob to ON position. Adjust ﬂame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position (see Figure 46). Note: The burner may light if hand-held remote was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the REMOTE or ON position when the pilot is not lit. This will drain the battery.

2.Set selector switch in the OFF position to prevent draining battery.

3.Turn off all electrical power to the appliance if service is to be performed.

4.Push in gas control knob slightly and turn clockwise to “OFF”.

5.Close lower louver panel.

Shutting Off Burners Only (pilot stays lit)

You may shut off the burners and keep the pilot lit by doing

Blower Control Knob

(Optional Accessory)

OFF

	Selector Switch	ON OFF REMOTE
	in Remote	ON OFF REMOTE
	in Remote
	Position

		Variable
		Control Knob
N
O		L
		L
T		O	I
L		O	H
O
I		F
	P F
Gas Control Knob
in ON Position

one of the following:
1.	Turn gas control knob clockwise	to the PILOT position.

2.Set selector switch in the OFF position.

Figure 46 - Setting the Selector Switch, Gas Control Knob and Variable Control Knob for Remote Operation

www.desatech.com

116192-01C