Desa VDCFTPA, VDCFRPA Optional Wireless HAND-HELD Remote Control Accessories, Installing Receiver

Page 19

INSTALLATION

Continued

OPTIONAL WIRELESS HAND-HELD

REMOTE CONTROL ACCESSORIES

Remote-Ready Models Only

([C]GHRCB Series & [C]GHRCTB

Series)

Installing Receiver

1.Disconnect wires from the control valve (see Figure 26) .

2.Locate the battery clip mounted on the back of the receiver (see Figure 27).

3.Slide 9-volt battery (not included) through the clip.

4.Attach the terminal wires to the battery (see Figure 27).

5.Connect wires from remote receiver to control valve as shown in Figure 28.

6.Install remote receiver unit onto remote/ blower bracket using screws provided (see Figure 28).

Figure 26 - Disconnecting Wires From

Control Valve

Receiver

Installing 9-Volt Battery in Hand-Held Remote Control Unit

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to the battery (not in- cluded). Place battery into the battery housing.

3.Replace battery cover onto remote control unit.

Terminal	Battery Cover		Remote
			Remote
			Control	Unit
Wires			Control	Unit
Wires
9-Volt
Battery
			Battery
			Housing
Figure 29 - Installing Battery in Hand-
Held Remote Control Unit
(GHRCB and CGHRCB Series)
Terminal Wires		Remote Control		Unit
Terminal Wires
9-Volt
Battery
			Battery
Battery			Cover
Battery
Housing
Figure 30 - Installing Battery in Hand-
Held Remote Control Unit
(GHRCTB and CGHRCTB Series)

9-Volt	Terminal
Battery	Wires
	Battery Clip

Figure 27 - Attaching Battery to Receiver

White Wire to

TH Terminal on

Control Valve

Remote

Receiver

Red Wire to

TPTH Terminal on

Control Valve

Figure 28 - Installing Remote Receiver

OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 (Remote-Ready Models Only)

WARNING: Read and fol- low installation instructions. Installation should be done by a qualiﬁed installer familiar with low-voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or ﬁre hazard will occur.

1.Remove jumper wire from control valve (see Figure 26).

113133-01B

www.desatech.com

19

Image 19

Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Safety Information Unpacking Product FeaturesProduct Identification Local CodesShoulder Screw Screen Hood AssemblySheet Metal Screws Hood Louver Firebox Top Tools Required Phillips screwdriverProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationTop Installation ItemsFireplace Clearances Minimum Clearance to Combustible MaterialsDepth BUILT-IN Fireplace InstallationActual Framing Height Front WidthTop Louver Bottom Louver Optional Mantel InstallationMantel Shelf Side of FireboxInstalling Optional Blower Accessory GA3450TA Switch Installing Blower AccessorySwitch Power Cord Plate Remote Wire Blower Harness Bracket Lower Louver DoorExtension Cord For Built-In InstallationBlower Bracket Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Gas Regulator or Gas Control Valve Equipment Pressure Testing Fireplace Gas ConnectionsEquipment Shutoff Valve Propane/LP Supply Tank Equipment Open Shutoff Valve ClosedVolt Terminal Battery Wires Battery Clip Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control UnitTerminal W Terminal R R Control Valve To Wall Thermostat or Switch Or SwitchFeed wires through rectangular slots Remove jumper wire from control valve see ,Lighting Instructions Installing LOG SET and ScreenFor Your Safety Read Before Lighting Operating FireplaceShutting Off Fireplace Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingOperating Blower Pilot Ignitor Burner Electrode Piezo Flame Control Ignitor Adjustment Knob ButtonPilot Burner Ignitor Electrode ON/OFF Series Model Cghrcb Manual ModeAuto Thermostatic Mode Optional HAND-HELD Remote OperationKey Pad Lock Feature Optional GWMS2 Wall Mounted SwitchSafety Features Auto Shutoff FeatureInspecting Burners Cleaning MaintenanceExterior LOG SETCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingModels Only Burner oriﬁce is clogged Clean burner see CleaningBurner oriﬁce is clogged Mote-Ready Models OnlyNance, When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringGas leak. See Warning Thermostat Models SpecificationsRemote-Ready Models Firebox Models VDC Illustrated Parts BreakdownNot a ﬁeld replacement part Parts ListThermostat Models Vdcftpa and Vdcftna Thermostat Models REMOTE-READY Models Vdcfrna and Vdcfrpa KEY Part Numbers Vdcfrpa Vdcfrna Description QTY Accessories For all models. Creates the sound of a real burn- ing ﬁre Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbReceiver and HAND-HELD Remote Control KIT Ghrcb Information VideoParts Under Warranty Replacement PartsService Hints Technical Service113133-01B Keep this Warranty Warranty InformationLimited Warranty VENT-FREE Compact Classic Hearth