®
VENTED NATURAL GAS LOGS
OPERATING
APPLIANCE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: Keep flue open when operating unit.
WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result caus- ing property damage, personal injury or loss of life.
BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•Do not try to light any appliance.
•Do not touch any electric switch; do not use any phone in your building.
•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
•If you cannot reach your gas supplier, call the fire department.
LIGHTING
INSTRUCTIONS
1.STOP! Read the safety information, above.
2.Turn the gas shutoff valve to OFF.
3.Wait five (5) minutes to clear out any gas. If you then smell gas STOP! Fol- low the safety information above. If you don't smell gas, go on to the next step.
4.Light a match and lay it on top of the pan material about 2" from the end of the supply side of the pan
5.Slowly turn the gas shutoff valve ON until the burner ignites. If the burner doesn’t ignite within 10 seconds with the match burning, turn the shutoff valve OFF and repeat steps 1 through 4 again.
GAS SHUTOFF
VALVE OPERATION
Flame Adjustment
1.Adjust the flame ON/OFF by turn-
ing the gas shutoff valve counter-
clockwise 
to open or clock-
wise 
to close, as necessary.
Shutting Off Appliance
1.Turn gas shutoff valve clockwise 
to the OFF position.
CURING LOGS
During the
•Ignite a 2" flame and maintain it for 1 hour.
•Burn the logs in consecutive 1 hour pe- riods raising the flame an additional 2" to full flame height for a total of three hours.
OPERATING
INSTRUCTIONS FOR
GA9000
Note: Operation instructions for GA9100 Remote Ready Valve/Pilot Kit will be included with the kit.
1.STOP! Read the safety information, column one this page.
2.Make sure manual shutoff valve is fully open.
3.Press in and turn control knob clock-
wise 
to the OFF position.
4.Wait five (5) minutes to clear out any gas. Then smell for gas around log set and near floor. If you smell gas, STOP! See Safety information, page 2 and Air For Combustion And Ventila- tion, pages 4 through 6. If you don’t smell gas, go to the next step.
5.Turn control knob counterclockwise 
to the PILOT position and press in. Keep control knob pressed in for five (5) seconds.
Note: You may be running this log set for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 sec- onds. This will allow air to bleed from the gas system.
•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.
6.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the rear of the front burner. If needed, keep pressing ignitor button until pilot lights.
Note: If pilot does not stay lit, con- tact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match.
7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.
Note: If pilot goes out, repeat steps 3 through 7.
8.Turn control knob counterclockwise 
to the ON position. Burner should light. If burner does not light, call a qualified service person.
Control Knob | ||||
Ignitor |
| Pilot |
| |
|
| ON | OFF | |
|
| FROM "PILOT" POSITION | ||
On |
| SLIGHT PUSH TO | Off | |
|
| PULL PUSH | ||
|
|
| TURN OFF |
|
ON OFF | FROM "PILOT" POSITION | SLIGHT PUSH TO TURN OFF PULL PUSH | TURN OFF PULL PUSH | TOPUSHSLIGHTPOSITION"PILOT"FROM OFFON |
Figure 21 - Ignitor and Control Knob | ||||
|
|
|
| Thermo- |
Pilot |
|
|
| couple |
Figure 22 - Thermocouple and Pilot
12 | 901265 |