INSTALLATION
Continued
Mantel Clearances for Built-In
Installation
If placing custom mantel above
CAUTION: Do not allow the
NOTICE: Surface temperatures ofadjacentwallsandmantelsbe- comehotduringoperation.Walls and mantels above the firebox may become hot to the touch. If installed properly, these tem- peratures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.
NOTICE: If your installation does notmeettheminimumclearances shown, you must do one of the following:
•raise the mantel to an accept- able height
•remove the mantel
BUILT-IN FIREBOX INSTALLATION
Wall board or facing |
|
|
|
| Mantel Shelf | ||||||||||
material (above |
|
|
|
| |||||||||||
|
|
|
| Note: Any portion of the | |||||||||||
firebox) may be of |
|
|
|
| |||||||||||
|
|
|
| mantel shelf must NOT | |||||||||||
combustible material, |
|
|
|
| |||||||||||
|
|
|
| extend beyond this profile. | |||||||||||
including decorative |
|
|
| 12" |
| ||||||||||
|
|
|
|
|
|
|
|
|
| ||||||
mantel ornaments or |
|
|
| 63/4" |
|
|
|
|
|
| |||||
other similar projec- |
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
| |||||
tions off of the facing |
|
| 11/2" |
|
|
|
|
|
| ||||||
|
|
|
|
|
| ||||||||||
material. |
|
|
|
|
|
|
|
|
|
|
| ||||
| Framing |
|
|
|
|
|
|
|
|
|
|
| |||
| Material |
|
|
|
|
| Noncombustible |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Material May |
| 12" | 16" | 20" | |
|
|
|
|
|
|
|
|
|
| Project Off this |
| ||||
| Firebox |
|
|
|
| Surface above |
|
|
|
|
| ||||
|
|
|
|
| the Firebox Hood |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Note: All vertical | ||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
| Supplied Firebox | measurements are | ||||||||||
|
| Screen |
|
| from top of fireplace | ||||||||||
|
|
|
| Hood Must Be | |||||||||||
|
|
|
|
|
|
|
| hood opening to | |||||||
|
|
|
|
|
|
|
| Used at All Times | |||||||
|
|
|
|
|
|
|
| bottom of mantel shelf. | |||||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| These minimum | ||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| clearances replace any | ||||
|
|
|
|
|
|
|
|
|
|
| other recommended | ||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| clearances supplied with | ||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| your ANSI Z21.11.2 | ||||
|
|
|
|
|
|
|
|
|
|
| approved gas logs. | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 7 - Minimum Mantel Clearances for Built-In Installation
www.desatech.com | 11 |