Framing, EB1 Receptacle Hookup, 20008662

Framing

Framing can be constructed before or after the ﬁreplace is set in place, however, most installers build the frame before setting the ﬁreplace.

Frame ﬁreplace with 2 x 4 lumber or heavier materi- als. Refer to framing dimensions in Figure 1 for basic ﬁreplace speciﬁcations.

NOTE: Framing should be positioned to accommodate wall covering and ﬁreplace facing material.

EB1 (Receptacle) Hookup

Option for Circulating Models Only

Wiring should be installed by a certiﬁed electrician.

Turn off circuit breaker before wiring models.

Once ﬁreplace is secured, complete wiring the fan kit. Remove knockout in the center of the back of the EB1 and install listed cable clamps. Feed electrical wire through listed cable clamp leaving approximately six (6) inches of wire exposed through the EB1. Secure listed cable clamp to the wire.

Attach white wire from power source to one (1) wire of receptacle and secure with nut. Attach black wire from power source to the other wire of receptacle and secure with nut. Be sure nuts are secured tightly.

Secure EB1 assembly to inside of electrical box cover- plate using two screws. Attach cover to face of the EB1 while being careful to position excess wire completely within the EB1, then attach coverplate to ﬁreplace.

Chimney Set-Up

Since you have already planned the chimney run, you should know exactly how the installation is to be ac- complished - how much pipe is required, the number of elbows, if any, and type of termination to be used.

CAUTION: Report to your dealer any parts damaged in shipment, speciﬁcally check the end connection of chimney sections and elbows.

NOTE: Fireplaces may use CFM Corporation Model SK8, or Model S (three wall) chimney systems. The BR/BC Series Fireplace will accept the SK8 chimney system as is; but a TWABR adapter collar is required when using the Model S (triple wall) chimney system. The installation procedure described in this manual applies only to the SK8 system. Either chimney system may be used, but may not be mixed.

Straight-Up Chimney Installation

To mark the centerline of the ﬂue, put the ﬁreplace in ﬁnal position and measure out from the wall: 9¹⁄₂" (241mm). Mark a spot on the ceiling directly above the ﬁreplace. Draw a line parallel to the back wall through this mark. (Fig. 8)

Vermont Castings EWF30

Chimney Centerline

Actual Centerpoint

9��" (241mm)

Plumb Line

Plumb Bob

Imaginary

Centerpoint

FP1563

Fig. 8 Locate centerline of chimney with plumb line.

Using a plumb bob positioned directly over center point of ﬁreplace ﬂue collar, mark the ceiling to establish the chimney center point. (Fig. 8)

Offset Installation

In order to clear an obstruction, it may be necessary to offset chimney from vertical. This is accomplished by using elbows. Use the 30˚ Offset Elbow table on Page 6 to determine proper offset and parts required.

Each offset requires two (2) elbows. The second elbow is equipped with support straps. It is very important to install the second elbow in each offset as close to the ceiling or support as possible so that the elbow straps can be secured to framing members to help support the

weight of the chimney.

Determine offset distance of your chimney arrangement from centerline of ﬁreplace to centerline of chimney where it is to pass through ceiling.

20008662

EWF30 specifications

The Vermont Casting EWF30 is a testament to innovation and craftsmanship in the world of cast iron wood stoves. This highly efficient wood-burning stove combines traditional aesthetics with modern technology, making it a perfect centerpiece for both rustic and contemporary homes. One of the standout features of the EWF30 is its impressive heating capacity. Designed to heat areas up to 2,000 square feet, it is ideal for large spaces, providing consistent warmth during chilly months.

Constructed from high-quality cast iron, the EWF30 offers a durability that only improves with age. This material is known for its excellent heat retention and distribution, resulting in a steady, comfortable warmth. The stove’s classic design includes large ceramic glass windows, allowing users to enjoy the mesmerizing beauty of the fire while safely keeping the warmth inside.

Incorporating advanced technology, the Vermont Casting EWF30 features a clean burning system that significantly reduces emissions. This is a critical aspect for environmentally conscious consumers, as the stove adheres to strict EPA standards, promoting cleaner air and reduced environmental impact. The efficiency of this wood stove is exceptional, with a thermal efficiency rating that maximizes heat output while minimizing fuel usage.

The EWF30 is equipped with a user-friendly air control system, allowing for easy adjustments to the airflow. This system enhances the combustion process, enabling users to achieve the desired flame and heat levels effortlessly. The top-loading design also simplifies the refueling process, making it easier to add wood without disturbing the existing fire.

Aesthetically, the Vermont Casting EWF30 can be customized with various finishes, including traditional black, enamel, and even bold colors, ensuring it fits seamlessly with any interior decor. Additionally, this model includes a removable ash pan, providing a convenient cleaning option.

In summary, the Vermont Casting EWF30 is more than just a wood stove; it is a fusion of tradition and technology. Its heating efficiency, durability, and aesthetic appeal make it a worthy investment for anyone seeking a reliable and stylish heating solution for their home. Whether for ambiance or functionality, the EWF30 is designed to enhance the living experience while respecting the environment.