Vermont Casting EWF30 Install Remainder of Chimney Sections, Finish Wall, Finishing, 20008662

Page 14
Install Remainder of Chimney Sections

Vermont Castings EWF30

There must be a 1¹⁄₂” (38 mm) air space between out- ermost portion of chimney sections and any adjacent combustible surfaces. (Combustible surfaces include burnable materials such as: ceiling members, joists, flooring, combustible insulation and roof structures.)

WARNING: Do not pack required air spaces with insulation or other materials.

Mark an outline of the roof hole around the center of the point nail. NOTE: Hole dimensions given in the chim- ney top installation instructions are horizontal dimen- sions; therefore, the hole size must be marked on the roof accordingly.

Cover the opening of the installed chimney so debris cannot get into the system.

Cut and frame the hole. It is good practice to use fram- ing lumber that is the same size as the rafters. Install the frame securely because the chimney top and flash- ing anchored to the frame must be able to withstand heavy winds.

Install Remainder of Chimney Sections

Since you have already preplanned the height of your termination according to the Ten Foot Rule, continue to install pipe to the predetermined height.

Check the chimney top installation instructions for details on how high above the roof top the chimney sec-

Finish Wall

Finish the wall with material of your choice. Do not install a combustible mantel shelf less than 12” (305 mm) above the firebox grille opening. Do not install a mantel face plate less than 6” (159 mm) from top of grille opening. (Fig. 21) If a combustible material is used below a flat mantel shelf, consult your local building codes for minimum clearance from top of fireplace opening to bottom of mantel shelf.

All joints (top, bottom and sides) where wall or decora- tive facing material meets fireplace surround must be completely sealed with a noncombustible material. (Fig- ures 20 and 24)

NOTE: No side wall protection is required for fireplaces installed at 45° to two (2) side walls (corner installation).

Air Space Clearances

Combustible framing material MUST NOT penetrate AIR SPACE (shaded areas)

1¹⁄₂”

 

(38 mm)

Standoff

 

tions (all pipes) should extend.

Install Top Housing or Termination

Follow the installation instructions provided with the

chimney termination you have selected.

Installing Chimney in a Chase

Refer to Figure 2, Page 5 for an illustration of a typical chase installation.

CAUTION: Treatment of firestop spacers and construc- tion of chase may vary with type of building. These instructions are not a substitute for local building codes. You must check your local building codes to determine specific requirements for your city or state. NOTE: Other building materials may be required in addition to

CFM Corporation Firestop Spacers.

Finishing

CAUTION: All joints between the finished wall and the fireplace surround (steel front) must be sealed with noncombustible material to prevent cold air leakage into the room. (Fig. 19)

1” (25mm) Air Finish WallInstall Top Housing or Termination Space to Sides

Wall

Shield

NO material may cover cast face

Hearth Extension Installing Chimney in a Chase

Firestop

1” (25mm) Space to Back

1” (25mm) Air Space to Sides

0” Clearance to Floor

FP1567

NOTE: No material may cover black cast face.

Fig. 19 Minimum clearances to combustibles.

14

20008662

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Homeowner’s Installation and Operating Manual EWF30 FireplaceCFM Specialty Home Products Do Not Discard This Manual Retain for Future UseVermont Castings EWF30 Table of ContentsIntroduction Save These Instructions for Future ReferenceDescription Safety InformationPrecautions DraftsEWF30 Woodburning Fireplace SpecificationsEWF30 Vermont Castings EWF3020008662 Chase InstallationVermont Castings EWF30 Chimney Requirements - Offset Installations 30˚ Elbow OffsetsIllustration Key Vermont Castings EWF30Planning the Chimney Run Planning InformationMounting the Fireplace The Ten Foot RuleChimney Supports InstallationChase Installation Insulating Fireplace Enclosure for Cold ClimatesFraming Straight-UpChimney InstallationOffset Installation EB1 Receptacle HookupCutting the Hole Positioning, Safety Strips Securing the FireplaceCeiling Chimney Hole Possible Obstructions Framing the Ceiling HoleInstallation Instructions Installing Outside Air KitInstallation Precautions Vermont Castings EWF30Proper Firestop Spacer Installation Installing the Chimney SystemInstalling the Firestop Spacer in the Ceiling HoleAdditional Ceilings Continue Installing Pipe to Complete RunCanadian Requirements for Insulation Shield Penetrating the RoofInstalling Chimney in a Chase Install Remainder of Chimney SectionsInstall Top Housing or Termination Finish WallSide Wall Protection Hearth InstallationMantels Vermont Castings EWF30Example of Determining Hearth Extension COMMON MATERIALS AND FACTORSVermont Castings EWF30 EquivalentsMinimum Wall Clearances Minimum Hearth Extension DimensionsVermont Castings EWF30 20008662The Damper OperationAttach Handles EWF30 ControlsGlass Doors Use the Air Control SettingsThe Fan Burn Only High-QualityWoodSpecial Tactics for Cold-ClimateHeating Starting and Maintaining a Wood FireReloading and Reviving a Wood Fire Vermont Castings EWF3020008662 Remove and Store Ash SafelyVermont Castings EWF30 Adjust the Door Latch Periodically MaintenanceCleaning the Glass How to Replace GasketsReplacing the Door Gaskets A Clean Chimney System is Safer and Works BetterThe Chimney System Replace Damaged Door Glass ImmediatelyVermont Castings EWF30 Maintenance ScheduleYearly Spring Cleaning Fireplace Daily20008662 Chimney ComponentsVermont Castings EWF30 Description EWF30 FireplaceVermont Castings EWF30 EWF30Ref. Description EWF30 Fireplace continuedVermont Castings EWF30 EWF30TWABR Optional AccessoriesFan Kit Screen KitModel Trim KitsVermont Castings EWF30 DescriptionVermont Castings EWF30 2000866220008662 WarrantyLimited 3 Year Warranty CFM Specialty Home Products
Related manuals
Manual 32 pages 45.68 Kb

EWF30 specifications

The Vermont Casting EWF30 is a testament to innovation and craftsmanship in the world of cast iron wood stoves. This highly efficient wood-burning stove combines traditional aesthetics with modern technology, making it a perfect centerpiece for both rustic and contemporary homes. One of the standout features of the EWF30 is its impressive heating capacity. Designed to heat areas up to 2,000 square feet, it is ideal for large spaces, providing consistent warmth during chilly months.

Constructed from high-quality cast iron, the EWF30 offers a durability that only improves with age. This material is known for its excellent heat retention and distribution, resulting in a steady, comfortable warmth. The stove’s classic design includes large ceramic glass windows, allowing users to enjoy the mesmerizing beauty of the fire while safely keeping the warmth inside.

Incorporating advanced technology, the Vermont Casting EWF30 features a clean burning system that significantly reduces emissions. This is a critical aspect for environmentally conscious consumers, as the stove adheres to strict EPA standards, promoting cleaner air and reduced environmental impact. The efficiency of this wood stove is exceptional, with a thermal efficiency rating that maximizes heat output while minimizing fuel usage.

The EWF30 is equipped with a user-friendly air control system, allowing for easy adjustments to the airflow. This system enhances the combustion process, enabling users to achieve the desired flame and heat levels effortlessly. The top-loading design also simplifies the refueling process, making it easier to add wood without disturbing the existing fire.

Aesthetically, the Vermont Casting EWF30 can be customized with various finishes, including traditional black, enamel, and even bold colors, ensuring it fits seamlessly with any interior decor. Additionally, this model includes a removable ash pan, providing a convenient cleaning option.

In summary, the Vermont Casting EWF30 is more than just a wood stove; it is a fusion of tradition and technology. Its heating efficiency, durability, and aesthetic appeal make it a worthy investment for anyone seeking a reliable and stylish heating solution for their home. Whether for ambiance or functionality, the EWF30 is designed to enhance the living experience while respecting the environment.
Top Page Image Contents