Char-Broil 466247310 manual Troubleshooting Electronic Ignition, Section

Page 30

Troubleshooting - Electronic Ignition

Problem (Ignition)

Possible Cause

Check Procedure

Prevention/Solution

 

 

 

 

SECTION I

• Battery not installed

• Check battery orientation.

• Install battery (make sure that “+” and “–”

No sparks appear at

any electrodes when

properly.

 

connectors are oriented correctly, with “+” end up

Electronic Ignition Button

 

 

and “–” end down.)

is pressed; no noise can

• Dead battery.

• Has battery been used

• Replace battery with new AA-size alkaline battery.

be heard from spark

module.

 

previously?

 

 

• Button assembly not

• Check to insure threads are

• Unscrew button cap assembly and reinstall, making

 

installed properly.

properly engaged. Button

sure threads are aligned and engaged fully.

 

 

should travel up and down

 

 

 

without binding.

 

 

• Faulty spark module.

• If no sparks are generated

• Replace spark module assembly.

 

 

with new battery and good

 

 

 

wire connections, module is

 

 

 

faulty.

 

 

 

 

 

SECTION II

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

No sparks appear at

any electrodes when

connections not

and tight?

module and electrodes.

Electronic Ignition Button

connected.

 

 

is pressed; noise can

 

 

 

be heard from spark

 

 

 

module.

 

 

 

 

 

 

 

SECTION III

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

Sparks are present

connections not

and tight?

module and electrodes.

but not at all

connected.

 

 

electrodes and/or not

• Arcing to grill away

• If possible, observe grill in

• If sparks are observed other than from burner(s),

at full strength

 

from burner(s).

dark location. Operate

wire insulation may be damaged. Replace wires.

 

 

ignition system and look for

 

 

 

arcing between output wires

 

 

 

and grill frame.

 

 

• Weak battery.

• All sparks present but weak

• Replace battery with a new AA-size alkaline battery.

 

 

or at slow rate.

 

 

• Electrodes are wet.

• Has moisture accumulated

• Use paper towel to remove moisture.

 

 

on electrode and/or in burner

 

 

 

ports?

 

 

• Electrodes cracked or

• Inspect electrodes for

• Replace cracked or broken electrodes.

 

broken “sparks at

cracks.

 

 

crack”.

 

 

 

 

 

 

30

Image 30
Contents Estimated assembly time 30 minutes Date PurchasedTable of Contents This Grill is for Outdoor USE onlyInstallation Safety Precautions California PropositionLP Cylinder Filling USE and CareLP Liquefied Petroleum Gas UL listed Overfill ProtectionFor your safety UseDo not household cleaning agents. Damage to gasLP Cylinder Leak Test Leak Testing Valves, Hose and Regulator Connection, do not use this regulatorTurn all grill control knobs to OFF For Safe Use of Your Grill and to Avoid Serious Injury Main Burner Lighting InstructionsBurner Flame Check Side Burner Lighting InstructionsSideburner Match Lighting Ignitor CheckStoring Your Grill General Grill CleaningCooking surfaces If a bristle brush is used to clean any SurfacesCleaning the Burner Assembly Turn gas off at control knobs and LP cylinderLimited Warranty Items Manufacturer will not PAY forParts List Not PicturedKey Qty Description Parts Diagram Fixed caster Locking caster AssemblyFront Bottom shelf RearGrill head Regulator hose Lower back panel Rear of Shelf Screws and Washers removed from valve bracket Now you may fully tighten lower screws on upper back panel Front of ShelfBack of main control panel Holes on fascia to Sideburner lid Front brace Page Wire Frontbrace Right door Cooking grate Cylinder screw at rear of cart Troubleshooting Emergencies Possible Cause Prevention/SolutionAUTO-CLEAN Troubleshooting Electronic Ignition SectionWarranty Registration Department Box Columbus, GA