Char-Broil 463222209 manual Troubleshooting Electronic Ignition, Section

Page 31

Troubleshooting - Electronic Ignition

Problem (Ignition)

Possible Cause

Check Procedure

Prevention/Solution

 

 

 

 

SECTION I

• Battery not installed

• Check battery orientation.

• Install battery (make sure that “+” and “–”

No sparks appear at

any electrodes when

properly.

 

connectors are oriented correctly, with “+” end up

Electronic Ignition Button

 

 

and “–” end down.)

is pressed; no noise can

• Dead battery.

• Has battery been used

• Replace battery with new AA-size alkaline battery.

be heard from spark

module.

 

previously?

 

 

• Button assembly not

• Check to insure threads are

• Unscrew button cap assembly and reinstall, making

 

installed properly.

properly engaged. Button

sure threads are aligned and engaged fully.

 

 

should travel up and down

 

 

 

without binding.

 

 

• Faulty spark module.

• If no sparks are generated

• Replace spark module assembly.

 

 

with new battery and good

 

 

 

wire connections, module is

 

 

 

faulty.

 

 

 

 

 

SECTION II

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

No sparks appear at

any electrodes when

connections not

and tight?

module and electrodes.

Electronic Ignition Button

connected.

 

 

is pressed; noise can

 

 

 

be heard from spark

 

 

 

module.

 

 

 

 

 

 

 

SECTION III

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

Sparks are present

connections not

and tight?

module and electrodes.

but not at all

connected.

 

 

electrodes and/or not

• Arcing to grill away

• If possible, observe grill in

• If sparks are observed other than from burner(s),

at full strength

 

from burner(s).

dark location. Operate

wire insulation may be damaged. Replace wires.

 

 

ignition system and look for

 

 

 

arcing between output wires

 

 

 

and grill frame.

 

 

• Weak battery.

• All sparks present but weak

• Replace battery with a new AA-size alkaline battery.

 

 

or at slow rate.

 

 

• Electrodes are wet.

• Has moisture accumulated

• Use paper towel to remove moisture.

 

 

on electrode and/or in burner

 

 

 

ports?

 

 

• Electrodes cracked or

• Inspect electrodes for

• Replace cracked or broken electrodes.

 

broken “sparks at

cracks.

 

 

crack”.

 

 

 

 

 

 

31

Image 31
Contents Product Guide Estimated assembly time 30 minutesINSTALLER/ASSEMBLER California Proposition Installation Safety PrecautionsLP Cylinder Filling LP Liquefied Petroleum GasLP Cylinder Leak Test LP Cylinder Exchange Connecting Regulator to the LP CylinderTurn all grill control knobs to OFF Leak Testing Valves, Hose and RegulatorMain Burner Ignitor Lighting For Safe Use of Your Grill and to Avoid Serious InjuryIgnitor Check Sideburner Match LightingBurner Flame Check Turning Grill OffCleaning the Burner Assembly General Grill CleaningStoring Your Grill Correct Engagement Reinstall Screws Grill Halogen Light Cleaning the Lens Limited Warranty Not Pictured Parts ListParts Diagram Rear AssemblySide of cart Control Panel Front Brace Inside of left side shelf Upper back panel Debris collecter PanelHoles on fascia to Sideburner grate #8x3/8 self-tapping screw Qty Heat shield Qty Emitter Plates Clarity of illustrationRear of grate Cooking grate Cylinder screw at rear of cart Emergencies Possible Cause Prevention/Solution TroubleshootingAUTO-CLEAN Section Troubleshooting Electronic IgnitionPage Page Page Warranty Registration Department Box Columbus, GA