Char-Broil 463230513 Heat Shield, Grease Tray, LP Cylinder Not included, Tank Retainer Screw

Page 27

15

B

•Attach the heat shield to grease tray with #8x3/8” sheet metal screws (A).

•Place grease pan into grease tray, then place the tray into the cart (B).

A	Heat Shield

#8x3/8"	Grease Tray
Sheet Metal Screws
Qty. 4

Grease Tray

Grease Pan

CAUTION

Failure to install grease tray and grease pan will cause hot grease to drip from bottom of grill with risk of fire or property damage.

•LP tank is sold separately. Use only with an OPD (over-fill protection device) equipped LP tank. Fill and leak-check before attaching

16	to grill and regulator. See Use and Care section to correctly Leak Test and perform the Burner Flame Check.

•Place Lp tank into hole in bottom shelf with tank collar opening facing front of grill as shown. Finger tighten tank retainer screw to hold LP tank securely in place. Insert regulator through the large hole on left side panel.

Always keep LP cylinders in upright position during use, transport, and storage.

CAUTION

Failure to install tank correctly may allow gas hose to be damaged in operation, resulting in the risk of fire.

Regulator

LP Cylinder

(not included)

Cylinder screw at rear of cart

Tank Retainer Screw

LP Tank

27

Image 27

Contents Date Purchased Product GuideThis Grill is for Outdoor USE only Table of ContentsCalifornia Proposition Installation Safety PrecautionsPre-Heating Your Grill Temperature Convective Grills onlyFirst Time Use Lava Rock / BriquettesRotisserie Cooking Food SafetyDirect Cooking Indirect CookingUsda Recommended Safe Minimum Internal Temperatures Storing Your Grill Why Clean?General Cleaning Routine CareUL listed Overfill Protection USE and CareLP Liquefied Petroleum Gas LP Cylinder FillingFor your safety LP Cylinder Leak TestNipple has to be centered into the LP cylinder valve Leak Testing Valves, Hose and Regulator Connection, do not use this regulatorTurn all grill control knobs to OFF Use grill at least 3 ft. from any wall or surface Safety TipsFor Safe Use of Your Grill and to Avoid Serious InjurySideburner Ignitor Lighting Ignitor LightingSear Burner Ignitor Lighting Sear Burner Match-LightingIgnitor Check General Grill CleaningBurner Flame Check Turning Grill OffTurn gas OFF at control knobs and LP cylinder Cleaning the Burner AssemblyStoring Your Grill Very Important Burner tubes must reengage valveItems Manufacturer will not PAY for Limited WarrantyNot Pictured Parts ListQty Description Key Qty DescriptionParts Diagram #8x3/8 Sheet Metal Screws Qty Assembly20x2-3/8 Machine Screw Qty Flange NutScrews Metal TabFlange Nut Qty 20x2-3/8 Machine Screw Weight Block 20x2 Machine Screw Qty 20x2 Machine ScrewFlange Nut Qty 20x1/2 Screw Qty Right side panel removed for clarityLock Washer Qty 7mm Fiber Washer 20x1/2 ScrewQty 20x1/2 7mm Screw Qty 20x1/2 Screw20x1/2 Machine Screw Qty 20x1/2 Screw Flange Nut 7mmSideburner Tube Ignitor WireSideburner Valve Venturi Clip #8-32x3/8#8 Wing nut Sideburner Bezel Sideburner Valve Sideburner Control Knob5mm Lock Washer Qty 5mm Flat Washer Qty Left DoorWarming Rack Leg Wire Pivot Wire Cooking Grate AA Battery Back PinSear Burner Tank Retainer Screw Heat ShieldGrease Tray LP Cylinder Not includedTroubleshooting Emergencies Possible Cause Prevention/SolutionProblem Possible Cause Prevention/Solution Problem Possible Cause Prevention/SolutionSection Troubleshooting Electronic IgnitionMail to / Enviar a / Envoyer à Special Offer