Brinkmann 2210 Series owner manual Grill Body Assembly

Page 27

Note: When performing Step 10, Lift grill body from front and rear panels to avoid injury to hands and fingers. Be sure to pass hose/regulator assembly above cart frame crossbar.

Step 10

With the help of a friend, place grill body assembly on preassembled cart frame. Grill body will rest on angled top of vertical supports. Align bolt holes located on the outside of the grill body assembly. Secure using four M6 X12mm bolts with small star washers.

Grill Body

Assembly

GRILL LIGHTING INSTRUCTIONS:

CENTER BURNER

 

ELECTRONIC IGNITER

FOR OUTDOOR

1.

Read and follow all warnings

4.

Push and turn the control knob for

7. To light the left and right

9. To turn off, turn each

USE ONLY

 

and instructions in owner’s

the CENTER BURNER to HIGH.

burners, push and turn

control knob clockwise

 

manual before lighting.

5.

Press the electronic igniter and

control knobs to HIGH.

until it locks in OFF

 

2.

Open lid before lighting burner.

 

hold for 3-5 seconds to light burner.

Follow Step 6.

position.

 

3.

Make sure all control knobs are

6.

If ignition does not occur in

8. Refer to owner’s manual

 

 

for match lighting

NOTE: Turn off LP supply

 

 

in the OFF position.

 

5 seconds, turn control knob

procedure.

 

 

NOTE: The CENTER BURNER must

 

to OFF, wait 5 minutes to allow gas

 

at cylinder when

FOR ASSISTANCE,

 

be lit first, then light the left and

 

to dissipate and repeat lighting

 

appliance is not in use.

 

right burners.

 

procedure.

 

 

 

CALL 800-527-0717

GRILL LIGHTING INSTRUCTIONS:

CENTER BURNER

 

ELECTRONIC IGNITER

FOR OUTDOOR

1.

Read and follow all warnings

4.

Push and turn the control knob for

7. To light the left and right

9. To turn off, turn each

USE ONLY

 

and instructions in owner’s

 

the CENTER BURNER to HIGH.

burners, push and turn

control knob clockwise

 

 

manual before lighting.

5.

Press the electronic igniter and

control knobs to HIGH.

until it locks in OFF

 

2.

Open lid before lighting burner.

 

hold for 3-5 seconds to light burner.

Follow Step 6.

position.

 

3.

Make sure all control knobs are

6.

If ignition does not occur in

8. Refer to owner’s manual

 

 

for match lighting

NOTE: Turn off LP supply

 

 

in the OFF position.

 

5 seconds, turn control knob

procedure.

 

 

NOTE: The CENTER BURNER must

 

to OFF, wait 5 minutes to allow gas

 

at cylinder when

FOR ASSISTANCE,

 

be lit first, then light the left and

 

to dissipate and repeat lighting

 

appliance is not in use.

 

right burners.

 

procedure.

 

 

 

CALL 800-527-0717

26

Image 27
Contents Gas Porcelain Outdoor Grill For Your Safety Important SafetyTable of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Regulator Resetting Procedure Filling the LP GAS CylinderHose and Regulator Connecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderLeak Testing When to Perform a Leak TestChecking for Leaks PRE-START Check List Lighting Instructions Lighting the Main BurnersMatch Lighting the Main Burners Lighting the Side Burner Match Lighting the Side BurnerTurning OFF the Grill Controlling FLARE-UPS Operating the GrillBreaking in Your Grill Preheating the GrillSide Burner Rotisserie CookingCleanliness Grilling to Proper TemperatureHelpful Hints Burner ASSEMBLY/MAINTENANCE Cleaning and MaintenanceBefore Storing Your Grill Cooking GrillsHeat Distribution Plates Transporting and StorageTrouble Shooting Frequently Asked Questions Frequently Asked Questions Parts BAG Contents Assembly Instructions For Missing PARTS, Please Call Customer Service AT Step Hubcap Tank Heat Shield Plate Place grease cup in middle of hole in heat shield plate Grill Body Assembly Step Hose Side Burner Igniter ProSeries 2210 Assembled Warranty