Philips FW930SR, FW930P2/2 manual Timer Setting, View Clock, Clock Setting

CLOCK

English	MINI HIFI SYSTEM	PROGRAM SHUFFLE			STEREO
		REPEAT TIMER REC			BACK
		NEWS T.A. AM MW FMLW			FRONT HSD
		60Hz	250Hz 500Hz	1KHz 2KHz 4KHz 8KHz
	STANDBY				DOLBY B
	ON				NR
					RDS
					RDS
	CLOCK/				NEWS/TA
	TIMER	CD1 • 2 • 3	BAND	TAPE 1 • 2	CDR

CD	TUNER	TAPE			AUX	VOLUME
PROG	STOP•CLEAR	SIDE A•B	▲	PRESET ▲		A. REVEV
SEARCH • TUNING		PLAY PAUSE	PREV		NEXT
DUB
(HSD)
						MIC
REC	SOUND NAVIGATION					LEVEL
INCREDIBLE		DYNAMIC BASS				MIC
	SURROUND	BOOST

DIGITAL

SOUND CONTROL

Notes:

–During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically.

–When a power interruption occurs, the clock setting is erased.

–To set the time with RDS clock, see "Receiving RDS Radio Station" under TUNER section.

Timer Setting

• The system can switch on to CD,

TUNER, or TAPE 2 mode automatically

at a preset time. It can serve as an

TIMER

•Before selecting CD or TAPE, make sure a CD or tape is loaded in the CD tray or

tape deck 2.

3Pressʈor ‡to set the hour for the timer to start.

4PressÊ’or ‘to set the minute for the timer to start.

5Press CLOCK/TIMER to store the start time.

ªThe timer is now set.

ªThe TIMER flag remains on the display.

• At the preset time, the timer will be activated.

ªThe selected source will be played.

Notes:

View Clock

You can view the clock (if it is set) while the system is in standby mode or any source mode. It will be displayed for about seven seconds.

•Press CLOCK/TIMER briefly (on the system only).

ª“10:38” (the current time) will be displayed.

ª“--:--” will be displayed if the clock is not set.

Clock Setting

The clock is set in 24-hour mode, e.g.

“00:00“ or “23:59“. Before setting the clock, you must be in the View Clock mode.

1Press CLOCK/TIMER to select clock mode.

ª“00:00” or the current time starts flashing.

2Set the hour withʈor ‡.

3Set the minute withÊ’or ‘.

4Press CLOCK/TIMER again to store the setting.

ªThe clock starts.

•To exit without storing the setting, press

‚on the system.

	alarm to wake you up.
•	Before setting the timer, make sure the
	clock is set correctly.
•	The timer will always be switched on
	once it is set.
•	The volume of the timer will start to
	increase from the minimum level
	until the volume level before the set
	is switched to standby mode.

1Press and hold CLOCK/TIMER for more than 2 seconds to select timer mode.

ª“00:00” or the last set timer starts flashing. The TIMER flag flashes.

ªThe last selected source is lit while other available sources are flashing.

2Press CD, TUNER or TAPE to select the desired source.

–During timer setting, if no button is pressed within 90 seconds, the system will exit timer setting mode automatically.

–If the source selected is TUNER, the last tuned frequency will be switched on.

–If the source selected is CD, playback will begin with the first track of the last selected disc. If the CD trays are empty, the TUNER will be selected instead.

–If the source selected is TAPE, and if the preset time is reached during high speed dubbing, the TUNER will be selected instead.

30