Pride Mobility 1103 ULTRA Foot Platform Depth Adjustment, Foot Platform Angle Adjustment

Page 26

V . C O M F O R T A D J U S T M E N T S

Foot Platform Depth Adjustment

To adjust the foot platform depth:

1.Remove the quick release fasteners from the foot platform bracket. See figure 17.

2.Move the foot platform in or out to the desired depth.

3.Reinstall the quick release fasteners into the foot platform bracket and tighten.

Quick Release Fasteners: The foot platform is attached to the power base with two quick release fasteners. See figure 17. Each quick release fastener consists of a bolt, a lever, and a nut. See figure 18. The lever has a cam on the end that allows it to clamp into place. The quick release fastener has two states: clamped and unclamped. When the lever is open, the quick release fastener is unclamped. When the lever is closed, the quick release fastener is clamped.

To clamp the quick release fastener:

1.Make sure the lever is in the open position.

2.Turn the nut clockwise until it is snug.

3.Rotate the lever until it is in the fully closed position.

NOTE: If the lever will not rotate to the fully closed position, then turn the nut counterclockwise one- quarter or one-half turn.

Foot Platform Angle Adjustment

You can adjust the angle of the foot platform with a hex key. See figure 19.

To adjust the foot platform angle:

1.Flip up the foot platform and locate the setscrew.

2.Turn the setscrew counterclockwise to raise the front of the foot platform.

3.Turn the setscrew clockwise to lower the front of the foot platform.

Controller Position

You can position the controller for either left-hand or right- hand use.

WARNING! Do not place the controller cable so that it can be pinched in the seat frame or the power base frame.

SETSCREW

Figure 19. Bottom View of Footrest

SETSCREW

Figure 20. Underside of Armrest

26

www.pridemobility.com

Jazzy 1103 Ultra

Image 26
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Authorized Pride ProviderProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsIncline Information Weight LimitationsTire Inflation Cornering Information Public Streets and Roadways Freewheel ModeBraking Information Stairs and Escalators Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Motor Vehicle Transport TransfersYou are transferring onto DoorsLift/Elevation Products Inclement Weather PrecautionsElevators Positioning BeltsBatteries AlcoholElectromagnetic and Radio Frequency Interference EMI/RFI Your Power Chair I . Y O U R P O W E R C H a I RJazzy 1103 Ultra Specifications Jazzy 1103 Ultra Power Base Electrical ComponentsJazzy 1103 Ultra Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatTo change the seat height Comfort AdjustmentsO M F O R T a D J U S T M E N T S Seat Position Seatback Angle AdjustmentTo adjust the seatback angle To change the positionFoot Platform Height Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Reclining SeatController Position Foot Platform Depth AdjustmentFoot Platform Angle Adjustment Swing-away Footrests Elevating Leg RestsHeavy Duty Drop-in Leg Rests Anti-Tip WheelsTo adjust the anti-tip wheels To use the swivel feature Power Elevating Seat OperationTo operate the power elevating seat Charging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging To break in new batteries for maximum efficiency To charge the batteries using the onboard chargerBattery Break-in Frequently Asked Questions FAQs How should I store my power chair and its batteries? Why do my new batteries seem weak?How can I ensure maximum battery life? What about public transportation?VSI consists I . O P E R a T I O NVSI Electronic Controller JoystickSpeed/Profile Keys Battery Condition MeterOn/Off Key Actuator Keys and Actuator Lights Motor ConnectorsBattery Connector Horn KeyVSI Error Codes Power Seat Actuator ConnectorCharger Inhibit Connector Thermal RollbackRemote Plus consists of the following Remote Plus ControllerRemote Plus Setting indicator Mode Key Speed SettingsMode key controls the speed settings. The Remote Plus To select a speed settingPower Accessories Optional Right/Left Turn Indicator Keys OptionalPower Accessory Indicator Optional Sleep ModeRemote Plus Error Codes Flashing Lights Diagnosis SolutionMicrodrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleError Codes To select a profile settingSpeed Adjustment Drive Profile SelectionFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection StorageBattery Replacement To replace the batteriesJazzy 1103 Ultra Battery Connections When to See Your Authorized Pride Provider for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byQuality Control- Jazzy 1103 Ultra Product Serial Number
Related manuals
Manual 47 pages 12.81 Kb