Pride Mobility 1103 ULTRA To charge the batteries using the onboard charger, Battery Break-in

Page 32

V I . B A T T E R I E S A N D C H A R G I N G

WARNING! Prevent injury and/or equipment damage! If your off-board battery charger has not been tested and approved for outdoor use, then do not expose it to adverse or extreme weather conditions. If the battery charger is exposed to adverse or extreme weather conditions, then it must be allowed to adjust to the difference in environmental conditions before use indoors. Refer to the manual supplied with the battery charger for more information.

To charge the batteries using the onboard charger:

1.Position the rear of your power chair close to a standard electrical outlet.

2.Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.”

3.Plug the charger power cord into the charger power cord receptacle on the power base, then into the electrical outlet.

NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is plugged into an electrical outlet.

4.We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly drops to 0.

NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. As the batteries charge, the ammeter needle slowly drops to 0. When the batteries are fully charged, the needle vibrates on or about the 0 mark on the ammeter.

5.When your power chair’s batteries are fully charged, disconnect the charger power cord, wind up the cord, and store it in a safe place.

To charge the batteries using the optional off-board charger:

1.Position the front of your power chair next to a standard electrical outlet.

2.Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.”

3.Plug the off-board charger into the off-board charger/programming socket on the controller. See VII. “Operation.”

4.Plug the off-board charger into the electrical outlet.

NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride off- board charger, then follow the instructions supplied by the manufacturer.

5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.

Battery Break-in

To break in new batteries for maximum efficiency:

1.Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level.

2.Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you become accustomed to the controls and break in the batteries.

3.Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now perform at over 90% of their potential.

4.After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.

32

www.pridemobility.com

Jazzy 1103 Ultra

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S IIISafety N T R O D U C T I O NPURCHASER’S Agreement Information ExchangePride Owners Club My Authorized Pride ProviderProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsIncline Information Weight LimitationsTire Inflation Cornering Information Public Streets and Roadways Freewheel ModeBraking Information Stairs and Escalators Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Transfers You are transferring ontoMotor Vehicle Transport DoorsInclement Weather Precautions ElevatorsLift/Elevation Products Positioning BeltsBatteries AlcoholElectromagnetic and Radio Frequency Interference EMI/RFI Your Power Chair I . Y O U R P O W E R C H a I RJazzy 1103 Ultra Specifications Jazzy 1103 Ultra Power Base Electrical ComponentsJazzy 1103 Ultra Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatTo change the seat height Comfort AdjustmentsO M F O R T a D J U S T M E N T S Seatback Angle Adjustment To adjust the seatback angleSeat Position To change the positionArmrest Width Adjustment Armrest Angle AdjustmentFoot Platform Height Adjustment Reclining SeatController Position Foot Platform Depth AdjustmentFoot Platform Angle Adjustment Swing-away Footrests Elevating Leg RestsHeavy Duty Drop-in Leg Rests Anti-Tip WheelsTo adjust the anti-tip wheels To use the swivel feature Power Elevating Seat OperationTo operate the power elevating seat Charging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging To break in new batteries for maximum efficiency To charge the batteries using the onboard chargerBattery Break-in Frequently Asked Questions FAQs Why do my new batteries seem weak? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?I . O P E R a T I O N VSI Electronic ControllerVSI consists JoystickSpeed/Profile Keys Battery Condition MeterOn/Off Key Motor Connectors Battery ConnectorActuator Keys and Actuator Lights Horn KeyPower Seat Actuator Connector Charger Inhibit ConnectorVSI Error Codes Thermal RollbackRemote Plus consists of the following Remote Plus ControllerRemote Plus Mode Key Speed Settings Mode key controls the speed settings. The Remote PlusSetting indicator To select a speed settingRight/Left Turn Indicator Keys Optional Power Accessory Indicator OptionalPower Accessories Optional Sleep ModeRemote Plus Error Codes Flashing Lights Diagnosis SolutionMicrodrive Controller Microdrive Controller consistsProfile and Speed Indicator Actuator IndicatorDisplay Pad Joystick Interface ModuleTo select a profile setting Speed AdjustmentError Codes Drive Profile SelectionFlashing Lights Diagnosis Solution Care and Maintenance Should your power chair come in contact with waterTemperature I I . C a R E a N D M a I N T E N a N C EDaily Checks Weekly ChecksTo check the brakes Monthly ChecksDisposal of Your Power Chair Cleaning and DisinfectionWheel Replacement StorageBattery Replacement To replace the batteriesJazzy 1103 Ultra Battery Connections When to See Your Authorized Pride Provider for Service Corrective MaintenanceW a R R a N T Y Reconditioned Units Warranty Warranty ExclusionsService Checks and Warranty Service Exclusions also include components with damage caused byQuality Control- Jazzy 1103 Ultra Product Serial Number
Related manuals
Manual 47 pages 12.81 Kb
Top Page Image Contents