Pride Mobility 1103 ULTRA owner manual Power Seat Actuator Connector, Charger Inhibit Connector

Page 38

V I I . O P E R A T I O N

Power Seat Actuator Connector

This connects the VSI to the power seat actuator.

Charger Inhibit Connector

The charger inhibit connector connects the VSI to the onboard battery charger. This connection provides an inhibit that disables the VSI when the battery charger is on. The charger inhibit connector is coded with colored dots. The dots are positioned so that you align the flat side of the male connector with the flat side of the female connector before making the connection.

WARNING! Failure to properly align the connectors can result in damage to the VSI, the charger, and the connectors.

Thermal Rollback

The VSI controller is equipped with a thermal rollback circuit. This circuit monitors the temperature of the controller, which roughly translates to motor temperature. In the event that the VSI controller becomes excessively hot (above 140° F), motor current (amperage) is reduced. For every degree above 140° F, the motor current limit is reduced by .55 amps until the VSI controller reaches 158° F, at which time the current output is reduced to zero. This reduces your power chair’s “power,” which could also reduce your power chair’s speed, and allows the electrical components and motors to cool down. When the temperature returns to a safe level, your power chair resumes its normal operation.

VSI Error Codes

The VSI controller is designed with the user’s safety as the prime consideration. It incorporates many sophisticated self- test features which search for potential problems at a rate of 100 times per second. If the VSI detects a problem either in its own circuits or in the power chair’s electrical system, it may decide to stop the power chair, depending on the severity of the problem. The VSI is designed to maximize the user’s safety under all normal conditions. The table below identifies the individual error codes. Error codes are displayed as a rapid flashing of the battery condition meter lights. If you get one of these error codes, contact your authorized Pride Provider.

FLASHING LIGHTS

DIAGNOSIS AND SOLUTION

 

 

1

The batteries need charging or there is a bad connection to the batteries. Check the

 

connections to the batteries. If the connections are good, try charging the batteries.

 

 

2

The left motor has a bad connection. Check the left motor connection.

 

 

3

The left motor has a short circuit to a battery connection. Contact your authorized Pride

 

Provider.

 

 

4

The right motor has a bad connection. Check the right motor connection.

 

 

5

The right motor has a short circuit to a battery connection. Contact your authorized Pride

 

Provider.

 

 

6

The power chair is being inhibited by the battery charger. Unplug the battery charger.

 

 

7

A joystick fault is indicated. Make sure that the joystick is in the neutral (center) position

 

before turning on the controller.

 

 

8

A controller system fault is indicated. Make sure that all connections are secure.

 

 

9

The parking brakes have a bad connection. Check the parking brake and motor

 

connections. Make sure the controller connections are secure.

 

 

10

An excessive voltage has been applied to the controller. This is usually caused by a poor

 

battery connection. Check the battery connections.

 

 

 

 

 

 

38

www.pridemobility.com

Jazzy 1103 Ultra

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Authorized Pride ProviderProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsIncline Information Weight LimitationsTire Inflation Cornering Information Public Streets and Roadways Freewheel ModeBraking Information Stairs and Escalators Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Motor Vehicle Transport TransfersYou are transferring onto DoorsLift/Elevation Products Inclement Weather PrecautionsElevators Positioning BeltsBatteries AlcoholElectromagnetic and Radio Frequency Interference EMI/RFI Your Power Chair I . Y O U R P O W E R C H a I RJazzy 1103 Ultra Specifications Jazzy 1103 Ultra Power Base Electrical ComponentsJazzy 1103 Ultra Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatTo change the seat height Comfort AdjustmentsO M F O R T a D J U S T M E N T S Seat Position Seatback Angle AdjustmentTo adjust the seatback angle To change the positionFoot Platform Height Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Reclining SeatController Position Foot Platform Depth AdjustmentFoot Platform Angle Adjustment Swing-away Footrests Elevating Leg RestsHeavy Duty Drop-in Leg Rests Anti-Tip WheelsTo adjust the anti-tip wheels To use the swivel feature Power Elevating Seat OperationTo operate the power elevating seat Charging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging To break in new batteries for maximum efficiency To charge the batteries using the onboard chargerBattery Break-in Frequently Asked Questions FAQs How should I store my power chair and its batteries? Why do my new batteries seem weak?How can I ensure maximum battery life? What about public transportation?VSI consists I . O P E R a T I O NVSI Electronic Controller JoystickSpeed/Profile Keys Battery Condition MeterOn/Off Key Actuator Keys and Actuator Lights Motor ConnectorsBattery Connector Horn KeyVSI Error Codes Power Seat Actuator ConnectorCharger Inhibit Connector Thermal RollbackRemote Plus consists of the following Remote Plus ControllerRemote Plus Setting indicator Mode Key Speed SettingsMode key controls the speed settings. The Remote Plus To select a speed settingPower Accessories Optional Right/Left Turn Indicator Keys OptionalPower Accessory Indicator Optional Sleep ModeRemote Plus Error Codes Flashing Lights Diagnosis SolutionMicrodrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleError Codes To select a profile settingSpeed Adjustment Drive Profile SelectionFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection StorageBattery Replacement To replace the batteriesJazzy 1103 Ultra Battery Connections When to See Your Authorized Pride Provider for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byQuality Control- Jazzy 1103 Ultra Product Serial Number
Related manuals
Manual 47 pages 12.81 Kb
Top Page Image Contents