Pride Mobility 1121 owner manual Seat Position Adjustment, Manual Recline Seatback Adjustment

Page 22

V . C O M F O R T A D J U S T M E N T S

Seat Position Adjustment

You can move the seat forward or rearward by changing the extrusion mounting position.

To change the position:

1.Turn off the power top the controller.

2.Remove the seat.

3.Remove both extrusions from the bottom of the seat. See figure 10.

4.Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backward. See figure 14.

5.Fasten the extrusions back onto the bottom of the seat.

6. Reinstall the seat.

Manual Recline Seatback Adjustment

If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base.

To adjust the seatback angle:

Figure 14. Seat Position Adjustment

 

1.

Pull up on the seatback release lever.

ARMREST ANGLE ADJUSTMENT SCREW

2.

Move the seatback down or up to the desired position.

 

3.

Release the lever.

 

Seatback Angle Adjustment

JAM NUT

 

If your power chair is equipped with an adjustable seatback, you can

 

adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.

 

To adjust the seatback angle:

ARMREST

1.

Remove the seatback angle adjustment screws on both seat hinges.

HEIGHT

 

See figure 15.

ADJUSTING

2.

Set the seatback at the desired angle.

SCREWS

3.

Reinstall the screws to both seat hinges and tighten.

SEATBACK

 

 

Armrest Width Adjustment

ANGLE

ADJUSTMENT

You can change each armrest’s width independently of each other.

SCREW

 

 

ARMREST

NOTE: Changing the armrest width may increase the overall

KNOB

width of your power chair.

 

To change the armrest width:

 

1.

Locate the two armrest knobs on each side of the armrest receiver

 

 

bracket. See figure 15.

 

2.

Loosen the knobs.

Figure 15. Seatback and Armrest

3.

Slide the armrests in or out to the desired width.

Adjustments

4.

Tighten the knobs.

 

22

www.quantumrehab.com

Quantum1121

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationOutdoor Driving Surfaces Stationary Obstacles Steps, Curbs, etc Freewheel ModePublic Streets and Roadways Stairs and Escalators Elevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingBatteries AlcoholElectromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R QuantumSpecifications Quantum 1121 Power Base Electronics Tray Active-Trac SuspensionManual Freewheel Lever To operate the dual manual freewheel leversSeat Installation Initial AssemblyA S S E M B L Y To install the seat O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightSeatback Angle Adjustment Seat Position AdjustmentManual Recline Seatback Adjustment Armrest Width AdjustmentFoot Platform Height Adjustment Armrest Height AdjustmentArmrestAngle Adjustment Foot Platform Depth AdjustmentSwing-away Footrests Foot Platform Angle AdjustmentElevating Leg Rests To adjust the anti-tip wheels Anti-Tip WheelsPower Elevating Seat Option Power Elevating Seat ActuatorTo operate the power elevating seat Power Elevating Seat OperationTo use the swivel feature Batteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in To charge the batteries using the off-board chargerTo charge the batteries using the optional onboard charger To break in new batteries for maximum efficiencyFrequently Asked Questions FAQs How should I store my power chair and its batteries? Why do my new batteries seem weak?How can I ensure maximum battery life? What type of batteries should I use?VSI consists I . O P E R a T I O NVSI Electronic Controller JoystickRed lights only lit or slow flash Charge batteries as soon Battery Condition MeterOn/Off Key Speed/Profile KeysCharger Inhibit Connector Actuator ConnectorController Connector Actuator Keys and Actuator Lights For Optional EquipmentVSI Error Codes Thermal RollbackRemote Plus Controller Remote Plus Master RemotePower Accessory Indicator Mode KeySpeed Setting Indicator Right/Left Turn Indicator KeysPower Accessories Speed SettingsTo select a speed setting Power ModuleActuator Lighting Module Not Shown Sleep ModeRemote Plus Trouble Codes Microdrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleError Codes To select a profile settingSpeed Adjustment Drive Profile SelectionFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning Instructions StorageBattery Replacement Battery Wiring Diagram LabelCorrective Maintenance When to See Your Quantum Rehab Specialist for ServiceTo replace the batteries W a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byQuality Control Quantum
Top Page Image Contents