Pride Mobility 1121 Actuator Lighting Module Not Shown, Sleep Mode, Remote Plus Trouble Codes

Page 39

V I I . O P E R A T I O N

Actuator Lighting Module (Not Shown)

The actuator lighting module is also located on the power base. The actuator lighting module provides a control and power interface between the power module, the lights, and/or the power seat actuator.

Sleep Mode

Your Remote Plus controller has a sleep mode feature. Sleep mode is a built-in circuit that automatically shuts off the main power if the joystick is not moved in any direction for approximately five minutes. The battery condition meter lights on the keypad indicate sleep mode by blinking once every five seconds. To restore power and continue, push the on/off key twice.

Thermal Rollback

The Remote Plus is equipped with a thermal rollback circuit. This circuit monitors the temperature of the motors, power module, and remote. In the event that any of them become excessively hot (above 122° F), motor voltage is reduced. For every degree above 122° F, the voltage is reduced by 5 volts. This reduces your power chair’s speed and allows the electrical components to cool down. When the temperature returns to a safe level, your power chair resumes its normal speed.

Remote Plus Trouble Codes

In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible problems with your power chair. The battery condition meter has ten lights. The lights provide information by the number of lights that are flashing. If any of the meter lights are flashing rapidly, the controller may be indicating a fault. For instance, if the first light is flashing rapidly, the battery voltage is nearly depleted. The following is a list of the possible errors signified by the rapidly flashing meter. When you get a trouble code, contact your Quantum Rehab Specialist.

FLASHING LIGHTS	DIAGNOSIS	SOLUTION

10	High Battery Voltage	Check batteries.

9	Solenoid Brake Fault	Check motor/brake wiring.

8	Possible Controller Fault	See Quantum Rehab Specialist.

7	Possible Joystick Fault	See Quantum Rehab Specialist.

6	Inhibit Active	Unplug charger. Check connections.

5	Right Motor Wiring Fault	Check right motor wiring.

4	Right Motor Disconnected	Check right motor wiring.

3	Left Motor Wiring Fault	Check left motor wiring.

2	Left Motor Disconnected	Check left motor wiring.

1	Low Battery Voltage	Check batteries/battery wiring.

Quantum1121

www.quantumrehab.com

39

Image 39

Contents Page F E T Y G U I D E L I N E S III N T E N T SInformation Exchange SafetyN T R O D U C T I O N PURCHASER’S AgreementMy Quantum Rehab Specialist Pride Owners ClubPre-Ride Safety Check S a F E T YModifications Weight Limitations Tire InflationIncline Information Braking Information Cornering InformationOutdoor Driving Surfaces Freewheel Mode Stationary Obstacles Steps, Curbs, etcPublic Streets and Roadways Stairs and Escalators Lift/Elevation Products TransfersDoors ElevatorsReaching and Bending Inclement Weather PrecautionsMotor Vehicle Transport Positioning BeltsAlcohol BatteriesElectromagnetic and Radio Frequency Interference EMI/RFI Quantum I . Y O U R P O W E R C H a I RSpecifications Quantum 1121 Power Base Active-Trac Suspension Electronics TrayTo operate the dual manual freewheel levers Manual Freewheel LeverInitial Assembly Seat InstallationA S S E M B L Y To install the seat To change the seat height Comfort AdjustmentsSeat Height and Seat Angle Adjustment O M F O R T a D J U S T M E N T SArmrest Width Adjustment Seat Position AdjustmentManual Recline Seatback Adjustment Seatback Angle AdjustmentFoot Platform Depth Adjustment Armrest Height AdjustmentArmrestAngle Adjustment Foot Platform Height AdjustmentFoot Platform Angle Adjustment Swing-away FootrestsElevating Leg Rests Anti-Tip Wheels To adjust the anti-tip wheelsPower Elevating Seat Actuator Power Elevating Seat OptionPower Elevating Seat Operation To operate the power elevating seatTo use the swivel feature B a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries To break in new batteries for maximum efficiency To charge the batteries using the off-board chargerTo charge the batteries using the optional onboard charger Battery Break-inFrequently Asked Questions FAQs What type of batteries should I use? Why do my new batteries seem weak?How can I ensure maximum battery life? How should I store my power chair and its batteries?Joystick I . O P E R a T I O NVSI Electronic Controller VSI consistsSpeed/Profile Keys Battery Condition MeterOn/Off Key Red lights only lit or slow flash Charge batteries as soonActuator Keys and Actuator Lights For Optional Equipment Actuator ConnectorController Connector Charger Inhibit ConnectorThermal Rollback VSI Error CodesRemote Plus Master Remote Remote Plus ControllerRight/Left Turn Indicator Keys Mode KeySpeed Setting Indicator Power Accessory IndicatorPower Module Speed SettingsTo select a speed setting Power AccessoriesSleep Mode Actuator Lighting Module Not ShownRemote Plus Trouble Codes Microdrive Controller consists Microdrive ControllerJoystick Interface Module Profile and Speed IndicatorActuator Indicator Display PadDrive Profile Selection To select a profile settingSpeed Adjustment Error CodesFlashing Lights Diagnosis Solution I I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesStorage Disposal of Your Power ChairCleaning Instructions Wheel ReplacementBattery Wiring Diagram Label Battery ReplacementWhen to See Your Quantum Rehab Specialist for Service Corrective MaintenanceTo replace the batteries W a R R a N T Y Exclusions also include components with damage caused by Reconditioned Units WarrantyWarranty Exclusions Service Checks and Warranty ServiceQuality Control Quantum