Quantum 1107 Seat Installation, To install the seat initial installation, To remove the seat

Page 22

I V . A S S E M B L Y / D I S A S S E M B L Y

Seat Installation

The Quantum 1107 use a seat interface system to attach the seat assembly to the power base assembly. This en- ables you to install and remove the seat quickly and easily. The main components are a pair of aluminum extrusions mounted to the underside of the seat base and seat inter- face mounted on the power base. See figures 11 and 12.

WARNING! Avoid injury! Do not pick up the seat assembly by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury or damage to the chair.

To install the seat (initial installation):

1.Prior to initial installation, the rear seat interface needs to be installed to the seat base.

2.Slide the rear seat interface into the rear extrusion. See figure 11.

3.Squeeze the retaining pin and clip it onto the rear seat interface.

4.Slide the seat onto the side frame handles and slowly lower the seat onto the front trapeze bar until it locks into place. See figure 12.

5.Flip the seat latch safety down. See figure 12.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

6.Install the controller into the mounting block under one of the armrests.

7.Tighten the setscrews in the mounting block. See figure 20.

8.Route the controller cable so that it cannot be pinched in the seat hinge.

9.Plug the controller into the connector on the power base. See figure 7.

10.Secure the controller cable to the armrest receiver with one or more wire ties.

To remove the seat:

1.Turn off the power to the controller.

2.Disconnect the controller

3.Flip up the seat latch safety.

4.Squeeze the seat latch together. See figure 12.

5.Pull the front of the seat up.

6.Slide the seat forward and off of the power base.

REAR EXTRUSION

REAR SEAT INTERFACE

RETAINING PIN

FRONT EXTRUSION

Figure 11. Rear Seat Interface Installation (Shown Without Armrests for Clarity)

SEAT LATCH SAFETY

SIDE

FRAME

HANDLES

SEAT LATCH

FRONT SEAT INTERFACE

Figure 12. Seat Installation (Shown Without Armrests for Clarity)

22

www.quantumrehab.com

Quantum 1107

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationOutdoor Driving Surfaces Stationary Obstacles Steps, Curbs, etc Freewheel ModePublic Streets and Roadways Stairs and Escalators Motor Vehicle Transport TransfersDoors Lift/Elevation Products Inclement Weather PrecautionsElevators Positioning BeltsPrescription Drugs/Physical Limitations Preventing Unintended Movement Removable Parts BatteriesAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R QuantumQuantum 1107 Specifications Quantum 1107 Power Base Electrical Components Quantum 1107 Electrical ComponentsManual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L Y / D I S a S S E M B L YTo install the seat initial installation Seat InstallationTo remove the seat Power Base Disassembly To disassemble the power chairQuantum 1107 Battery Box Removal and Frame Separation O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightArmrest Width Adjustment Seatback Angle AdjustmentManual Recline Seatback Adjustment Seat PositionTo change the armrest angle Armrest Angle AdjustmentTo change the armrest width Controller PositionFoot Platform Angle Adjustment Foot Platform Height AdjustmentFoot Platform Depth Adjustment Quick Release FastenersElevating Leg Rests Optional Swing-away FootrestsMulti-Axis Foot Plate Anti-Tip Wheels Adjustment O M F O R TBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries To break in new batteries for maximum efficiency Battery Break-inFrequently Asked Questions FAQs How does the charger work?How often must I charge the batteries? Can I use a different battery charger?Why do my new batteries seem weak? Daily UseWhat about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?Flight consists I . O P E R a T I O NFlight Controller JoystickOn/Off Key Battery Condition MeterLock Mode Actuator Keys and Actuator Lights For Optional EquipmentError Code Probable Cause Possible Solution Sleep Mode If EnabledError Codes Horn KeyVSI Electronic Controller VSI consistsRed lights only lit or slow flash Charge batteries as soon Speed/Profile KeysLocking/Unlocking the VSI Actuator Connector OptionalController Connector To lock the VSIVSI Error Codes Thermal RollbackRemote Plus Controller Remote Plus consists of the followingMode Key Speed Settings To select a speed settingSleep Mode Right/Left Turn Indicator Keys OptionalPower Accessories/Power Accessory Indicator Optional Light Key OptionalRemote Plus Error Codes Flashing Lights Diagnosis SolutionMicrodrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleDrive Profile Selection To select a profile settingSpeed Adjustment To change the speedFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksCleaning and Disinfection Disposal of Your Power ChairWheel Replacement Battery Replacement To replace the batteriesWhen to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S T E S Quality Control Quantum
Related manuals
Manual 2 pages 6.57 Kb

1107 specifications

Quantum 1107 represents a significant advancement in the realm of quantum computing, designed to address the growing complexities of computational tasks across various industries. This cutting-edge system leverages quantum bits, or qubits, which form the foundation of its unique processing abilities, allowing for operations that significantly outpace traditional binary computing.

One of the standout features of the Quantum 1107 is its impressive qubit count. With over 100 qubits, it is engineered to handle intricate calculations and simulations that would take classical computers an impractical amount of time. Each qubit is constructed using superconducting materials, allowing for high coherence times that enhance reliability and performance. This stability is critical for executing precise operations, ultimately expanding the potential applications of quantum algorithms.

The Quantum 1107 employs a novel quantum error correction technology, which is essential for maintaining the integrity of quantum calculations. By continuously monitoring and correcting errors that may arise during computations, this system ensures that users can trust the results produced, facilitating more complex problem-solving without the usual risk of errors that plague many quantum computing systems.

Furthermore, the system implements advanced quantum entanglement protocols, enabling qubits to work together in ways that amplify processing power. This phenomenon allows for simultaneous computations that drastically reduce the time required to solve specific algorithms, such as those in optimization, cryptography, and complex simulations.

Quantum 1107 also features a user-friendly interface that simplifies the programming of quantum applications. With built-in support for high-level programming languages designed for quantum computing, researchers and developers can easily implement quantum algorithms without needing to delve into the underlying hardware intricacies.

Another aspect of the Quantum 1107 is its robust scalability. This system is designed to grow alongside technological advancements, allowing for seamless upgrades in qubit count and processing capabilities. As the field of quantum computing continues to evolve, the Quantum 1107 remains positioned to adapt, ensuring that users can leverage the latest innovations.

In summary, Quantum 1107 stands out in the quantum computing landscape due to its high qubit count, advanced error correction, and entanglement capabilities, combined with a user-friendly interface and scalability. These features make it an invaluable tool for researchers and industries seeking to unlock the transformative potential of quantum technology.
Top Page Image Contents