Quantum 1107 I I . C a R E a N D M a I N T E N a N C E, Care and Maintenance, Temperature

Page 50

V I I I . C A R E A N D M A I N T E N A N C E

CARE AND MAINTENANCE

Your power chair is a sophisticated device. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your Quantum Rehab Specialist. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or operation, contact your Quantum Rehab Specialist.

WARNING! Prevent injury. Do not service the power chair when the seat is occupied.

Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas of any kind.

WARNING! Direct exposure to water or dampness could cause the power chair to malfunction electronically and mechanically. Water can cause electrical components to corrode and the chair’s frame to rust.

Should your power chair come in contact with water:

1.Dry your power chair as thoroughly as possible with a towel.

2.Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.

3.Check the joystick operation and the brakes before using your power chair again.

4.If any inconsistencies are found, take your power chair to your Quantum Rehab Specialist.

Temperature

!Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your power chair between the temperatures of 18° F and 122° F.

!In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell).

!Temperatures above 122° F may cause your power chair to operate at a reduced speed. This reduced speed is a safety feature built into the controller that helps prevent damage to the motor and other electrical components. See VII. “Operation.”

General Guidelines

!Avoid knocking or bumping the controller, especially the joystick.

!Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.

!Keep the controller clean.

!Check all connectors to ensure that they are all tight and secured properly.

!Make sure the drive tires are inflated to 35 psi (2.4 bar) if equipped with pneumatic tires.

WARNING! Overinflating tires can cause them to explode and can result in personal injury.

WARNING! Do not use a high pressure hose to inflate your tires.

!Use a rubber conditioner on the tire sidewalls to help preserve them.

WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the tires slippery and cause your power chair to skid.

50

www.quantumrehab.com

Quantum 1107

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsIncline Information Weight LimitationsTire Inflation Outdoor Driving Surfaces Braking InformationCornering Information Public Streets and Roadways Stairs and Escalators Freewheel ModeStationary Obstacles Steps, Curbs, etc Doors TransfersMotor Vehicle Transport Lift/Elevation Products Inclement Weather PrecautionsElevators Positioning BeltsAlcohol Preventing Unintended Movement Removable Parts BatteriesPrescription Drugs/Physical Limitations Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R QuantumQuantum 1107 Specifications Quantum 1107 Power Base Electrical Components Quantum 1107 Electrical ComponentsManual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L Y / D I S a S S E M B L YTo remove the seat Seat InstallationTo install the seat initial installation Power Base Disassembly To disassemble the power chairQuantum 1107 Battery Box Removal and Frame Separation O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightArmrest Width Adjustment Seatback Angle AdjustmentManual Recline Seatback Adjustment Seat PositionTo change the armrest angle Armrest Angle AdjustmentTo change the armrest width Controller PositionFoot Platform Angle Adjustment Foot Platform Height AdjustmentFoot Platform Depth Adjustment Quick Release FastenersMulti-Axis Foot Plate Swing-away FootrestsElevating Leg Rests Optional Anti-Tip Wheels Adjustment O M F O R TCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging To break in new batteries for maximum efficiency Battery Break-inFrequently Asked Questions FAQs How does the charger work?How often must I charge the batteries? Can I use a different battery charger?Why do my new batteries seem weak? Daily UseWhat about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?Flight consists I . O P E R a T I O NFlight Controller JoystickOn/Off Key Battery Condition MeterLock Mode Actuator Keys and Actuator Lights For Optional EquipmentError Code Probable Cause Possible Solution Sleep Mode If EnabledError Codes Horn KeyVSI Electronic Controller VSI consistsRed lights only lit or slow flash Charge batteries as soon Speed/Profile KeysLocking/Unlocking the VSI Actuator Connector OptionalController Connector To lock the VSIVSI Error Codes Thermal RollbackRemote Plus Controller Remote Plus consists of the followingMode Key Speed Settings To select a speed settingSleep Mode Right/Left Turn Indicator Keys OptionalPower Accessories/Power Accessory Indicator Optional Light Key OptionalRemote Plus Error Codes Flashing Lights Diagnosis SolutionMicrodrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleDrive Profile Selection To select a profile settingSpeed Adjustment To change the speedFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection Battery Replacement To replace the batteriesWhen to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S T E S Quality Control Quantum
Related manuals
Manual 2 pages 6.57 Kb

1107 specifications

Quantum 1107 represents a significant advancement in the realm of quantum computing, designed to address the growing complexities of computational tasks across various industries. This cutting-edge system leverages quantum bits, or qubits, which form the foundation of its unique processing abilities, allowing for operations that significantly outpace traditional binary computing.

One of the standout features of the Quantum 1107 is its impressive qubit count. With over 100 qubits, it is engineered to handle intricate calculations and simulations that would take classical computers an impractical amount of time. Each qubit is constructed using superconducting materials, allowing for high coherence times that enhance reliability and performance. This stability is critical for executing precise operations, ultimately expanding the potential applications of quantum algorithms.

The Quantum 1107 employs a novel quantum error correction technology, which is essential for maintaining the integrity of quantum calculations. By continuously monitoring and correcting errors that may arise during computations, this system ensures that users can trust the results produced, facilitating more complex problem-solving without the usual risk of errors that plague many quantum computing systems.

Furthermore, the system implements advanced quantum entanglement protocols, enabling qubits to work together in ways that amplify processing power. This phenomenon allows for simultaneous computations that drastically reduce the time required to solve specific algorithms, such as those in optimization, cryptography, and complex simulations.

Quantum 1107 also features a user-friendly interface that simplifies the programming of quantum applications. With built-in support for high-level programming languages designed for quantum computing, researchers and developers can easily implement quantum algorithms without needing to delve into the underlying hardware intricacies.

Another aspect of the Quantum 1107 is its robust scalability. This system is designed to grow alongside technological advancements, allowing for seamless upgrades in qubit count and processing capabilities. As the field of quantum computing continues to evolve, the Quantum 1107 remains positioned to adapt, ensuring that users can leverage the latest innovations.

In summary, Quantum 1107 stands out in the quantum computing landscape due to its high qubit count, advanced error correction, and entanglement capabilities, combined with a user-friendly interface and scalability. These features make it an invaluable tool for researchers and industries seeking to unlock the transformative potential of quantum technology.
Top Page Image Contents