Pride Mobility Jet 10 owner manual Monthly Checks, Yearly Checks, Storage

Page 36

X . C A R E A N D M A I N T E N A N C E

MONTHLY CHECKS

νCheck that the anti-tip wheels are not rubbing the ground when you are operating the Jet 10. Adjust them as necessary. See VI. “ComfortAdjustments.”

νCheck for extreme wear on the anti-tip wheels. Replace them as necessary.

νCheck for drive tire wear. See an your authorized Pride provider for replacement.

νCheck the rear casters for wear. Replace them as necessary.

νCheck the rear forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings replaced. See an your authorized Pride provider for repair.

νKeep your Jet 10 clean and free of foreign material, such as mud, dirt, hair, food, and drink.

YEARLY CHECKS

Take your Jet 10 to an authorized Pride provider for yearly maintenance. This helps ensure that your Jet 10 is functioning properly and helps prevent future complications.

STORAGE

Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the Jet 10. See IX. “Batteries and Charging.”

WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged.

CLEANING INSTRUCTIONS

CAUTION! Never hose off your power chair or place it in direct contact with water. Your Jet 10 has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth.

CAUTION! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become slippery or dry out and crack. Use soapy water and dry the seat thoroughly.

WHEEL REPLACEMENT

Your Jet 10 is equipped with solid tires. Periodically check the tires for excessive wear. If your tire requires replacement, you must replace the entire wheel assembly. Replacement wheel assemblies are readily available at your authorized Pride provider.

Follow these easy steps for a quick and safe wheel replacement:

1.Use a 5/32-in. hex key to remove the hub cap. See figure 25.

2.Use an 11/16-in. wrench to remove the drive wheel nut from the center hub of the wheel. See figure 26.

3.Pull the wheel assembly off of the axle.

4.Slide the new wheel assembly back onto the axle.

5.Install the drive wheel nut into the center hub and tighten.

6.Install the hubcap.

36

www.pridemobility.com

Jet 10/Rev H/Feb03

Image 36
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N IntroductionInformation Exchange Pride Owners Club My Authorized Pride Provider IsPre-Ride Safety Check S a F E T YModifications Weight Limitations Tire InflationIncline Information Braking Information Cornering InformationFreewheel Mode Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Public Streets and RoadwaysStairs and Escalators DoorsElevators EMI & RFIMotor Vehicle Transport TransfersPositioning Belts Inclement Weather Precautions Reaching and Bending BatteriesAlcohol Removable PartsFrequently Asked Questions Faqs Where do radio waves come from?I . E M I / R F EMI/RFI WarningsWhat is the FDA doing about the problem? What should I do if my power chair moves unexpectedly?Are all electric mobility vehicles susceptible to EMI/RFI? Y O U R J E T 1 Your JetSpecifications Electrical Connectors and Components Utility TrayTo engage or disengage the freewheel feature Manual Freewheel LeversSeat Installation To install the seatJoystick Installation To install the joystick controllerPin Controller Connector C O M F O R T a D J U S T M E N T S Seat HeightTo change the seat height Armrest WidthArmrest Angle Armrest Height OptionalJoystick Extension Footrest Height Footrest AngleElevating LEG Rests Option To adjust the ELR length Required Tool 13 mm wrench To adjust the anti-tip wheelsANTI-TIP Wheels Battery Removal I . D I S a S S E M B L YSeat Removal Body Shroud RemovalI I . O P E R a T I O N Dynamic DL ControllerTo operate your Jet Trouble Codes B a T T E R I E S a N D C H a R G I N G BatteriesCharging the Batteries To charge the batteries using the onboard charger Battery BREAK-INOFF-BOARD Charger To break in new batteries for maximum efficiencyBatteries and CHARGING-FREQUENTLY Asked Questions Faqs Daily USEInfrequent USE What type of battery should I use? Why do my new batteries seem weak?How can I ensure maximum battery life? How should I store my Jet 10 and its batteries? What about public transportation?What about shipping? Routine Maintenance TemperatureA R E a N D M a I N T E N a N C E Should your Jet 10 come in contact with waterDaily Checks Weekly ChecksTo check the brakes Cleaning Instructions Wheel Replacement Monthly ChecksYearly Checks StorageBattery Replacement To replace the batteriesWhen to see Your Authorized Pride Provider for Service Motor BrushesTo inspect or replace the motor brushes Corrective Maintenance O P T I O N S a N D a C C E S S O R I E S FIVE-YEAR Limited Frame Warranty ONE-YEAR Limited WarrantyWarranty Exceptions Warranty ExclusionsThere is no other express warranty Quality Control Model