Pride Mobility Jet 10 To charge the batteries using the onboard charger, OFF-BOARD Charger

Page 30

I X . B A T T E R I E S A N D C H A R G I N G

To charge the batteries using the onboard charger:

1.Position the rear of your Jet 10 close to a standard wall outlet.

2.Be certain the controller power is turned off and the manual freewheel levers are in the engaged position. See IV. “Your Jet 10.”

3.Remove the battery charger cord from the back pouch of your Jet 10 and plug it into the battery charger AC power cord receptacle located on the power base. See figure 4.

4.Extend the charger power cord and plug it into the wall outlet. The Jet 10 incorporates an inhibit function that disables the power chair when the charger is plugged into a wall outlet.

5.The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the charger to warm up. The ammeter may move as high as 5.5 amps, then gradually move back down to zero amps as the batteries charge.

6.We recommend you charge the batteries for 8 to 14 hours.As the batteries charge, the ammeter needle slowly drops to zero. When the batteries are fully charged, the needle vibrates on or about the zero mark on the ammeter scale.

7.When your Jet 10’s batteries are fully charged, you can unplug the power cord from the wall outlet, wind it up using the hook and loop strap, and place the cord back into the Jet 10’s back pouch.

OFF-BOARD CHARGER

If your Jet 10 is equipped with an off-board charger, follow these instructions.

1.Position your Jet 10 next to a standard wall outlet.

2.Be certain the controller power is turned off.

3.Remove the run plug (located where the charger harness would normally plug into the power base). See figure 4. This activates the inhibit function.

4.Plug the 3-pin extension cable from the charger into the connector where the run plug was removed.

5.Plug the charger into the wall outlet.

6.The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the charger to come up to normal operating temperature. The ammeter should move to 5 amps, then gradually move back down to 0 amps.As the batteries are charged, the ammeter needle will slowly drop to zero. When the batteries are fully charged, the needle vibrates on or about 0 amps. We recommend you charge the batteries for 8 to 14 hours.

7.When your Jet 10’s batteries are fully charged, disconnect the charger cord from the wall outlet and the charger from the power base.

8.Reconnect the run plug into its connector.

NOTE: If the run plug is not reconnected, your Jet 10 will not run.

BATTERY BREAK-IN

To break in new batteries for maximum efficiency:

1.Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level.

2.Operate your Jet 10 throughout the house and yard. Move slowly at first, and don’t stray too far until you become accustomed to the controls and break in the batteries.

30

www.pridemobility.com

Jet 10/Rev H/Feb03

Image 30
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N IntroductionInformation Exchange Pride Owners Club My Authorized Pride Provider IsPre-Ride Safety Check S a F E T YModifications Weight Limitations Tire InflationIncline Information Braking Information Cornering InformationStationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Public Streets and RoadwaysElevators Stairs and EscalatorsDoors EMI & RFIMotor Vehicle Transport TransfersPositioning Belts Inclement Weather Precautions Reaching and Bending BatteriesAlcohol Removable PartsI . E M I / R F Frequently Asked Questions FaqsWhere do radio waves come from? EMI/RFI WarningsWhat is the FDA doing about the problem? What should I do if my power chair moves unexpectedly?Are all electric mobility vehicles susceptible to EMI/RFI? Y O U R J E T 1 Your JetSpecifications Electrical Connectors and Components Utility TrayTo engage or disengage the freewheel feature Manual Freewheel LeversJoystick Installation Seat InstallationTo install the seat To install the joystick controllerPin Controller Connector To change the seat height C O M F O R T a D J U S T M E N T SSeat Height Armrest WidthArmrest Angle Armrest Height OptionalJoystick Extension Footrest Height Footrest AngleElevating LEG Rests Option To adjust the ELR length Required Tool 13 mm wrench To adjust the anti-tip wheelsANTI-TIP Wheels Seat Removal Battery RemovalI . D I S a S S E M B L Y Body Shroud RemovalI I . O P E R a T I O N Dynamic DL ControllerTo operate your Jet Trouble Codes B a T T E R I E S a N D C H a R G I N G BatteriesCharging the Batteries OFF-BOARD Charger To charge the batteries using the onboard chargerBattery BREAK-IN To break in new batteries for maximum efficiencyBatteries and CHARGING-FREQUENTLY Asked Questions Faqs Daily USEInfrequent USE What type of battery should I use? Why do my new batteries seem weak?How can I ensure maximum battery life? How should I store my Jet 10 and its batteries? What about public transportation?What about shipping? A R E a N D M a I N T E N a N C E Routine MaintenanceTemperature Should your Jet 10 come in contact with waterDaily Checks Weekly ChecksTo check the brakes Yearly Checks Cleaning Instructions Wheel ReplacementMonthly Checks StorageBattery Replacement To replace the batteriesWhen to see Your Authorized Pride Provider for Service Motor BrushesTo inspect or replace the motor brushes Corrective Maintenance O P T I O N S a N D a C C E S S O R I E S Warranty Exceptions FIVE-YEAR Limited Frame WarrantyONE-YEAR Limited Warranty Warranty ExclusionsThere is no other express warranty Quality Control Model