Pride Mobility INFMANU3890 manual Main Circuit Breaker Reset Button, Securing the Scooter

Page 23

I I I . Y O U R S C O O T E R

WARNING! When your scooter is in freewheel mode, the braking system is disengaged. Disengage the drive motors only on a level surface.

Ensure the key is removed from the key switch.

Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on a scooter to do this.

After you have finished pushing your scooter, always return it to the drive mode to lock the brakes.

NOTE: If the scooter is placed in freewheel mode (manual freewheel lever forward) while the key is in the “on” position, the scooter will not run until the manual freewheel lever is pushed backward and the key is turned to the “off” position, then back to the “on” position.

Main Circuit Breaker (Reset Button)

When the voltage in the batteries becomes low or your scooter is heavily strained because of excessive loads, the main circuit breaker may trip to protect the motor and electronics from damage. When the breaker trips, the entire electrical system shuts down. See figure 7.

The reset button pops out when the breaker trips. Allow a minute or so for the electronics to “rest.” Push in the reset button to reset the breaker.

If the breaker trips frequently, you may need to charge the batteries more often or have your authorized Pride Provider perform a load test on the batteries.

If the main circuit breaker trips repeatedly, see your authorized Pride Provider for service.

SECURING THE SCOOTER

Always secure the scooter in a forward-facing position in the vehicle. Attach the four tie-down straps to the designated securement points. See figures 8 and 9. Tighten the straps to sufficiently remove all slack. Never attach tie-downs to adjustable, moving, or removable parts of the scooter such as armrests, shrouds, and wheels. These items should be removed. Position the anchor points for the rear tie-down straps directly behind the rear securement points on the scooter. The front tie-down straps should anchor to floor points that are spaced wider than the scooter to provide increased lateral stability.

WARNING! Ensure scooters are properly secured to the motor vehicle during transport. Scooters that are not properly secured can become a hazard to the user and to other vehicle passengers in the event of a crash, sudden stopping, or swerving, as the scooter could tip or slide out of place.

FRONT SECUREMENT POINTS

Figure 8. Front Section

REAR SECUREMENT POINT

Figure 9. Rear Section

Pursuit

www.pridemobility.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Pursuit F E T Y G U I D E L I N E S N T E N T S Shipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Modifications Removable Parts PRE-RIDE Safety CheckGeneral Incline Information Weight LimitationsTire Inflation S a F E T Y Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesDoors Inclement Weather PrecautionsFreewheel Mode Stairs and EscalatorsBatteries Battery Disposal and RecyclingElevators Lift SYSTEMS/ELEVATION ProductsReaching and Bending Motor Vehicle TransportGetting Onto and OFF of Your Scooter ALCOHOL/SMOKING Positioning BeltsPrescription DRUGS/PHYSICAL Limitations Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R S C O O T E R Speed Adjustment DialKey Switch Battery Condition MeterStatus LED Turn Signal ButtonsLights Switch Hazard Lights SwitchElectrical System Fuses Hi-Low SwitchOff-board Charger Port Anti-Tip Wheels Motor/Transaxle AssemblyRear Section BatteriesSecuring the Scooter Main Circuit Breaker Reset ButtonCharging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCan I use a different charger? Frequently Asked QuestionsFollow these easy steps to charge the batteries How does the charger work?How can I get maximum range or distance per charge? How can I ensure maximum battery life?What type and size of battery should I use? How often must I charge the batteries?Battery Removal/Installation How do I change a battery in my scooter?What about public transportation? Why do my new batteries seem weak?Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Before Getting Onto Your ScooterGetting OFF of Your Scooter Power Down Timer FeatureMirror Position Tiller Angle AdjustmentSeatback Adjustment C O M F O R T a D J U S T M E N T SSeat Height Adjustment Seat Rotation AdjustmentFRONT-TO-BACK Seat Adjustment I . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblySee figure AssemblyFrame Separation Diagnostic Fault Codes I I . B a S I C TroubleshootingWhat if the main circuit breaker repeatedly trips? Tire Pressure Wheel ReplacementC a R E a N D M a I N T E N a N C E Exterior Surfaces Cleaning and DisinfectionBattery Terminal Connections Wiring HarnessesStoring Your Scooter Fuse ReplacementNylon Lock NUT Replacement Event a fuse should cease to workP E N D I X I Specification S Dimensions T E S Page INFMANU3890
Top Page Image Contents