Pride Mobility INFMANU3890 manual Frame Separation, Assembly, See figure

Page 34

V I I . D I S A S S E M B L Y A N D A S S E M B L Y

Frame Separation

1.Arrange the front wheel(s) in a straight for- ward-facing position.

2.Lower the tiller.

NOTE: The pivoting tiller is equipped with a mechanism that will lock the front wheels in place when the tiller is completely lowered and secured.

3.Grasp and lift up on the frame release lever. See figure 21.

4.Lift the front section up until the frame hooks of the front section separate from the rear sec- tion. See figure 22.

5.Slowly separate the two sections. See figure 22.

ASSEMBLY

1.Position the front and rear sections of your scooter as shown in figure 22.

2.Use the frame release lever to lift the front section as you align the frame hooks of the front section with the lower frame tube of the rear section. See figure 21.

3.Once the frame hooks are over the lower frame tube, lower the front section com- pletely. This will engage the frame lock.

4.Raise the tiller.

5.Connect the front-to-rear cable.

6.Reinstall the battery spacers if applicable.

See figure 23.

7.Reinstall the batteries to the battery wells.

8Connect both battery harnesses. See figure 20.

9.Secure the battery tie-down strap.

10.Reinstall the battery shroud.

11.Reinstall the seat and rotate it into place.

FRAME

RELEASE

LEVER

Figure 21. Frame Release Lever

LOWER FRAME TUBE

FRAME HOOKS

Figure 22. Frame Separation

TIE-DOWN STRAP

BATTERY SPACERS

Figure 23. Battery Spacers

34

www.pridemobility.com

Pursuit

Image 34

Contents Pursuit F E T Y G U I D E L I N E S N T E N T S PURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y General Removable Parts PRE-RIDE Safety CheckModifications Tire Inflation Weight LimitationsIncline Information S a F E T Y Cornering Information Braking InformationOutdoor Driving Surfaces Correct Curb ApproachStairs and Escalators Inclement Weather PrecautionsFreewheel Mode DoorsLift SYSTEMS/ELEVATION Products Battery Disposal and RecyclingElevators BatteriesGetting Onto and OFF of Your Scooter Motor Vehicle TransportReaching and Bending Prescription DRUGS/PHYSICAL Limitations Positioning BeltsALCOHOL/SMOKING Electromagnetic and Radio Frequency Interference EMI/RFI Battery Condition Meter Speed Adjustment DialKey Switch I . Y O U R S C O O T E RHazard Lights Switch Turn Signal ButtonsLights Switch Status LEDOff-board Charger Port Hi-Low SwitchElectrical System Fuses Batteries Motor/Transaxle AssemblyRear Section Anti-Tip WheelsMain Circuit Breaker Reset Button Securing the ScooterBatteries and Charging Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Charging Your BatteriesHow does the charger work? Frequently Asked QuestionsFollow these easy steps to charge the batteries Can I use a different charger?How often must I charge the batteries? How can I ensure maximum battery life?What type and size of battery should I use? How can I get maximum range or distance per charge?How do I change a battery in my scooter? Battery Removal/InstallationWhy do my new batteries seem weak? What about public transportation?Before Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Getting Onto Your ScooterPower Down Timer Feature Getting OFF of Your ScooterC O M F O R T a D J U S T M E N T S Tiller Angle AdjustmentSeatback Adjustment Mirror PositionFRONT-TO-BACK Seat Adjustment Seat Rotation AdjustmentSeat Height Adjustment Disassembly I . D I S a S S E M B L Y a N D a S S E M B L YFrame Separation AssemblySee figure I I . B a S I C Troubleshooting Diagnostic Fault CodesWhat if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Wheel ReplacementTire Pressure Wiring Harnesses Cleaning and DisinfectionBattery Terminal Connections Exterior SurfacesEvent a fuse should cease to work Fuse ReplacementNylon Lock NUT Replacement Storing Your ScooterP E N D I X I Specification S Dimensions T E S Page INFMANU3890