Pride Mobility Legend 4-Wheel Scooter owner manual I . C a R E a N D M a I N T E N a N C E

Page 38

X I I . C A R E A N D M A I N T E N A N C E

Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride Provider.The following areas require periodic inspection and/or care and maintenance.

TIRE PRESSURE

νIf equipped with pneumatic tires, always maintain a proper 30-35 psi tire pressure.

WARNING! It is important that 30-35 psi tire pressure be maintained in pneumatic tires at all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure in pneumatic tires at all times may result in tire and/or wheel failure, causing serious personal injury and/or damage to your scooter.

νRegularly inspect your scooter’s tires for signs of wear.

EXTERIOR SURFACES

Bumpers, tires, trim, and the tiller boot can benefit from an occasional application of rubber or vinyl conditioner.

WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat, floorboard, or tire tread. They will become dangerously slippery and result in personal injury and/or damage to your scooter.

BATTERY TERMINAL CONNECTIONS

νMake certain that the terminal connections remain tight and uncorroded.

νThe batteries must sit flat in the battery wells.

νThe battery terminals should face the rear of the scooter.

WIRING HARNESSES

νRegularlycheckallwiringconnections.

νRegularly check all wiring insulation, including the charger power cord, for wear or damage.

νHave your authorized Pride Provider repair or replace any damaged connector, connection, or insulation that you find before using your scooter again.

ABS PLASTIC SHROUDS

νThe front tiller shroud, front shroud, and the rear shroud are formed from durableABS plastic and are coated with an advanced formula urethane paint.

νAlightapplicationofcarwaxwillhelptheshroudsretain theirhighgloss.

AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY

These items are all prelubricated, sealed, and require no subsequent lubrication.

MOTOR BRUSHES

The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for wear by your authorized Pride Provider.

38

www.pridemobility.com

Legend

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Ultimate In Style & Performance F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N Information ExchangeQuick Reference Information Pride Owners ClubMy Authorized Pride Provider Is Modifications S a F E T YGeneral Removable Parts Electromagnetic FieldsTire Inflation PRE-RIDE Safety CheckWeight Limitations Incline InformationWheel Maximum Recommended Cornering Information Braking InformationOutdoor Driving Surfaces Streets and Roadways Stationary Obstacles STEPS, CURBS, ETCInclement Weather Precautions Freewheel Mode Doors Battery Disposal and RecyclingStairs and Escalators ElevatorsMotor Vehicle Transport Reaching and BendingAlcohol Positioning BeltsPrescription DRUGS/PHYSICAL Limitations I . E M I / R F EMI/RFI Frequently Asked Questions FaqsWhere do radio waves come from? EMI/RFI WarningsWhat should I do if my mobility vehicle moves unexpectedly? What is the FDA doing about the problem?Are all electric mobility vehicles susceptible to EMI/RFI? Specification S Usable Material Gray vinyl or Gray fabric Standard Seat Weight 45 lbs Drive SystemBattery Requirements MotorO U R L E G E N D Tiller ConsoleHazard Lights Switch Running Lights SwitchHeadlight Switch Turn Signal ButtonsRear Section Charger Power Cord ReceptacleMain Circuit Breaker Reset Button AmmeterBatteries Not Shown Motor/Transaxle AssemblyManual Freewheel Lever Anti-Tip WheelsCharging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Frequently Asked Questions Faqs What type and size of battery should I use? How can I get maximum range or distance per charge?How can I ensure maximum battery life? How should I store my scooter and its batteries?Before Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksI . O P E R a T I O N Getting Onto Your ScooterGetting OFF of Your Scooter Remove the key from the key switchPower Down Timer Feature I I . C O M F O R T a D J U S T M E N T S Tiller Angle AdjustmentSeat Rotation Adjustment Seat Height Adjustment Seatback AdjustmentArmrest Angle Adjustment Power Seat Optional Disassembly D I S a S S E M B LY a N D a S S E M B LYToggle Latch Release Frame SeparationAssembly Frame SectionsP T I O N a L a C C E S S O R I E S What if all the systems on my scooter seem to be dead? B a S I C TroubleshootingDiagnostic Flash Codes B a S I C Troubleshooting I . C a R E a N D M a I N T E N a N C E Rear Lights Fuse ReplacementCONSOLE, CHARGER, and Rear Electronics Storing Your ScooterONE-YEAR Limited Warranty THREE-YEAR Limited WarrantyTHREE-YEAR Warranty Exceptions Warranty ExclusionsT E S T E S T E S Susquehanna Ave. Exeter, PA
Top Page Image Contents