V I I I . C O M F O R T A D J U S T M E N T S
POWER SEAT (OPTIONAL)
Your scooter may be equipped with a power seat option, a power seat switch will be located on the tiller console. See figure 5. The power seat will be equipped with one of two operating systems. Refer to figures 12 and 13 to determine which system your scooter uses and follow the appropriate instructions for safe operation.
WARNING! The power seat is intended for operation only while your scooter is stationary and on a level surface. Its purpose is to aid you in reaching objects. Drive your scooter only with the power seat in the lowest position. Driving the scooter with power seat elevated could result in personal injury, equipment and/or property damage.
Strict adherence to the following safety rules is vital to your safety:
!Operate the power seat only while completely stationary on level ground.
!Do not press the throttle control lever and the power seat switch at the same time.
!Do not operate your scooter with the power seat elevated. Operate the scooter only with the power seat fully retracted (in the lowest position).
!Never place your scooter in freewheel mode with the power seat elevated.
!Use extreme caution when reaching for objects with your power seat elevated. Do not overextend or attempt to pick up objects that might affect your balance.
!Do not attempt ot raise or lower the seat while in motion.
Before operating the power seat, ensure your scooter is level and stationary and the speed adjustment dial is set to the slowest setting.
I X . D I S A S S E M B LY A N D A S S E M B LY
DISASSEMBLY
You can disassemble the scooter into seven pieces: the seat, the front section, the rear section, the rear shroud, the basket, and the batteries. See figure 14. No tools are required to disassemble or assemble your scooter, but keep in mind that the disassembled sections of the scooter take up more floor space than the assembled unit. Always disassemble or assemble your scooter on a level, dry surface with sufficient room for you to work and move around your
WARNING! Lifting weight beyond your physical capability may result in personal injury. Ask for assistance when necessary while disassembling or assembling your scooter.
SEAT
REAR SHROUD
BATTERIES
REAR SECTION
System 1 - Operation using power seat switch and throttle control lever:
1.Release the throttle control lever.
2.Toggle the power seat switch located on the tiller console to the “on” position. See figure 12.
3.To raise the power seat, operate your throttle con- trol lever in the forward direction.
4.Release the throttle control lever when you have attained your desired height.
5.To lower the power seat, operate your throttle control lever in the reverse direction.
6.Ensure your seat is in the lowest position and that you have fully released the throttle control lever.
7.Toggle “off” the power seat switch before you at- tempt to drive your scooter again.
POWER SEAT
SWITCH
THROTTLE
CONTROL LEVER
Figure 12. Power Seat Switch (With Vertical Line And Circle) Used In Conjuction With Throttle Control Lever to Activate The Power Seat Actuator (Switch Shown In The “Off” Position)
System 2 - Operation with power seat switch only:
1.To raise the power seat, press and hold the upper part of the switch. Release the switch when you have attained your desired height or upon reaching the high- est position. See figure 13.
2.To lower the power seat, press and hold the lower part oftheswitch.Releasetheswitchwhenyouhaveattained yourdesiredheightorupon reachingthelowestposition.
NOTE: The scooter must be stopped in order for the power seat to be operated. If the power seat switch is pressed while the scooter is in motion, the scooter will slow and come to a stop. The scooter may also produce a fault code indicated by the Status LED on the console. If a fault code occurs, you will need to turn the scooter’s power off then back on again before proceeding.
Figure 13. Power Seat Switch (With No Markings)-Activates The Power Seat Actuator
FRONT SECTION
BASKET
Figure 14. The Legend Disassembled
1.Place the manual freewheel lever in the drive (down) position.
2.Coil the charger power cord and store it for future use.
3.Push forward on the seat rotation lever to rotate the seat; lift the seat up and off the scooter. See figure 15.
4.Gently pull the shroud away from the frame at the bottom and lift it off of the scooter. See figure 16.
5.Disconnect the battery strap.
PULL SHROUD AWAY
FROM FRAME HERE
BEFORE LIFTING
SHROUD UP
Figure 15. Removing The Seat | Figure 16. Rear Shroud Removal |
34 | www.pridemobility.com | Legend | Legend | www.pridemobility.com | 35 |