Invacare 65500 Replacing Spartan Canes and Brakes, Preparing Spartan for Brake Replacement Figure

Page 4

REPLACING SPARTAN CANES AND BRAKES

Preparing Spartan for Brake Replacement (FIGURE 2)

1.Perform one (1) of the following:

INSTALLING BRAKE KIT (BEFORE 3/7/00) - Re- move EXISTING hand brake.

A.Remove the hex bolt, washer and locknut secur- ing the hand brake to the push handle.

B.Remove the hand brake.

INSTALLING BRAKE KIT (AFTER 3/8/00) - Re- move EXISTING hand brake.

A.Remove EXISTING hand grip from the push handle and discard.

B.Remove the phillips screw securing the EXIST- ING hand brake to the push handle.

C.Pull the EXISTING hand brake off of the push handle.

2.Perform one (1) of the following:

INSTALLING BRAKE KIT - Proceed to STEP 3.

INSTALLING CANE KIT - Remove the push handle. Perform the following:

A.Rotate adjustment lever counterclockwise to loosen. DO NOT remove.

B.Pull UP on the push handle to remove.

3.Remove the tire. Perform the following:

A.Remove the cap covers from both sides of the tire.

B.Remove the screw and locknut that secure the tire to the rollator.

C.Remove the tire.

4.Replace the brake. Refer to REPLACING SPARTAN BRAKES in this procedure of the instruction sheet.

REMOVING THE HAND BRAKE - STEP 1 (BEFORE 3/7/00) (BRAKE KITS ONLY)

REMOVING THE HAND BRAKE - STEP 1 (AFTER 3/8/00) (BRAKE KITS ONLY)

Hex Bolt

(STEP 1A)

Washer

(STEP 1A)

Locknut

(STEP 1A)

Push Handle

Hand Brake

(STEP 1B)

Phillips

Push Handle

Screw

 

Hand Grip

Hand Brake

REMOVING PUSH HANDLE - STEP 2REMOVING THE TIRE - STEP 3 (CANE KITS ONLY)

Push

 

 

Cap Cover (STEP 3A)

 

 

 

Handle

 

 

Tire (STEP 3C)

(STEP 2B)

 

 

 

 

 

 

Locknut (STEP 3B)

 

 

Screw

 

 

Adjustment

(STEP 3B)

Cap Cover

 

 

 

 

(STEP 3A)

 

Lever

 

 

 

 

 

(STEP 2A)

 

 

 

 

 

FIGURE 2 - REPLACING SPARTAN CANES AND BRAKES - PREPARING SPARTAN FOR BRAKE

REPLACEMENT

4

Image 4
Contents Safety Summary Replacing Sprint Canes and Brakes FigureSecurely tighten the locknut Install the NEWbrake wire. Perform the followingNEW hand brake Disassembled Assembled Preparing Spartan for Brake Replacement Figure Replacing Spartan Canes and BrakesAssemble the plunger assembly. Perform the following Removing/Installing The Spartan Brake Pad Only FigureReplacing Spartan Brakes Figure Install tire. Perform the following Assembling Spartan For Use FigureInstalling Brake KIT After 3/8/00 Install NEW hand brake Push the NEW hand brake onto the push handleAdjusting Sprint Spartan Hand Brakes Adjusting Cable Brake Handle Before 3/7/00Adjusting Cable Brake Handle Before 3/8/00 Loosen the brake handle adjustment nut by turningLoosen the cable brake adjuster unit locknut Retighten the cable adjuster unit locknutTo decrease tension, turn the cable adjuster unit Do one 1 of the followingAdjusting Stingray and Stargazer Push Handle Figure Replacing Stingray and Stargazer Brakes FigureAdjusting Stingray and Stargazer Hand Brakes Figure Adjusting Hand BrakeAdjusting Caster Housing Loosen the hand brake adjustment nut by turningTest brake, if necessary adjust brake Removing/Installing The Stingray Brake Pad FigureBly and securely tighten the set screw