B.Remove the hand brake.
C.Turn the adjustment lever COUNTERCLOCK- WISE.
D.Insert push handles into side frames with the hand grip facing the back of the rollator.
3.Perform one (1) of the following:
INSTALLING BRAKE KIT (BEFORE 3/7/00) - Install NEW hand brake.
A.Position the handbrake assembly under the push handle so the lock button is facing OUT, the tip of the hand brake is towards the end of the hand grip and the brake cable is AWAY from the hand grip.
B.Position the hook portion of the hand brake clamp through the slot in the hand brake assembly.
C.Install the washer, hex bolt and locknut to secure the hand brake assembly to the push handle.
D.Securely tighten the locknut.
INSTALLING BRAKE KIT (AFTER 3/8/00) - Install
NEW hand brake.
A. Push the NEW hand brake onto the push handle.
NOTE:Ifnecessary,twistthehandbrakewhilepushingto installonthepushhandle.
B.AlignthemountingholesoftheNEWhandbrakewith themountingholeinthepushhandle.
C.Installthephillipsscrewthroughbothmountingholes. Securelytighten.
D.Apply a thin coat of hair spray on the inside of the foam grip and on the push handle.
NOTE: This application will make it easier to slide the grip onto the push handle.
E. Slide new grip onto one end of the push handle.
4.Adjust the push handle. Refer to ADJUSTING SPRINT ANDSPARTANPUSHHANDLESinthisinstructionsheet.
5.Adjust the hand brake. Refer to ADJUSTING SPRINT ANDSPARTANHANDBRAKESinthisinstructionsheet.
INSTALLING/REMOVING THE HAND | INSTALLING/REMOVING THE HAND | |||||||
BRAKE (BEFORE 3/7/00) - STEPS 2 AND 3 | BRAKE (AFTER 3/8/00) - STEPS 2 AND 3 | |||||||
Hex Bolt (STEPS | Hand Brake Clamp (STEP 3B) | Hand Brake | Phillips Screw | |||||
|
|
| Hook (STEP 3B) | Adjustment | ||||
2A AND 3C) |
|
|
| |||||
|
|
|
|
| ||||
|
|
|
|
|
| Nut | Mounting Hole | |
Washer (STEPS |
|
|
| Slot (STEP 3B) |
|
|
| |
2A AND 3C) |
|
|
|
|
|
| ||
|
|
|
|
|
| |||
Locknut (STEPS |
|
|
|
| Lock Button |
|
| Hand Grip |
|
|
|
|
|
| |||
2A AND 3C) |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Push Handle | |
Push Handle |
|
|
| Hand Brake (STEP | Hand Brake Nut | |||
|
|
|
| 2B AND 3A) | Hand Brake | |||
|
|
|
|
|
|
|
|
|
INSTALLING PUSH HANDLE | INSTALLING THE TIRE - STEP 1 | ||||
| - STEPS 2 AND 3 |
|
| Cap Cover (STEP 3A) | |
Push Handle |
|
| Hand Grip |
| |
|
|
|
| ||
|
| (STEP 3A) |
|
| |
(STEPS 2D |
|
|
| Tire (STEP 3C) | |
|
|
|
| ||
AND 3A) |
| Textured | Tip of Hand |
|
|
|
|
|
| ||
|
| Brake |
|
| |
Brake Cable |
| Tubing |
| Locknut (STEP 3B) | |
| (STEP 3A) |
| |||
(STEP 3A) |
|
| Screw |
| |
|
|
|
| ||
|
| Adjustment Lever | (STEP 3B) | Cap Cover | |
|
| (STEP 2A) |
| (STEP 3A) | |
|
|
| |||
FIGURE 5 - REPLACING SPARTAN CANES AND BRAKES - ASSEMBLING SPARTAN FOR USE
7