Toshiba SL-9000 owner manual Operating Procedures, How to access REG., M.DOWN, or Rewrap menu

Page 66

14. OPERATING PROCEDURES

■ NOTES BEFORE STARTING OPERATION

14. OPERATING PROCEDURES

■NOTES BEFORE STARTING OPERATION

(1) Insert the power plug into the AC outlet and turn the power ON.

(2) A sixteen-second scanning will be performed after pressing the POWER key.

(3)Do not move the unit while it is in operation. Should it become necessary to move it at any time, turn the power switch to the OFF position and be sure to readjust the level indicator after relocating the scale.

(4)Should a power failure occur during operation, remove the commodity from the platter and insert the power plug into an AC outlet again when power is restored.

(5)If the scale is used with an unrated power source, inaccurate scaling or other errors may occur.

(6)If the zero point has shifted during scaling, and no tare is displayed, adjust the zero point by depressing the ZERO key.

(7)Check the date of the scale before operation every day.

(8)Make a test print before operation every day. Press the TEST key, and the test label is issued.

■How to access REG., M.DOWN, or REWRAP menu

The following display is the REG. menu display. When this display is shown after pressing

the POWER key, you can start the REG. operation right away.

<REG.> MANU. WEIGH ENTER THE PLU #

	lb	UNIT/$	TOTAL $
	0.000	P	000000

To access a menu from other menus, press the ESC. key to show the Main menu and enter the menu No. When the M.DOWN and REWRAP menus are protected, enter the menu No. and then the password.

<Menu> MAIN
0.	PROG.	5.	READ
1.	REG.	6.	RESET
2.	MARK DOWN	7.
3.	REWRAP	8.
4.	SECURITY	9.

NOTE: If a label nothing is printed or is issued after a printed label in batch mode, refer to Section 11.11 and press the SET NEXT key.

14- 1

Image 66

Contents SL-9000/9000N-FFR-US/CA/QR Page Safety Summary Precautions Table of Contents 14.1 13.113.2 14.2Introduction Accessories Applicable ModelSpecification ScaleSTLAN-2P OptionLON TmccAppearance Label Guide Printer Cover Main Power SwitchAdjustable Legs Meat Platter Power Cord Level GaugeDisplay US TypeCA/QR Type KEY Layout Programming KeyboardProgramming Keyboard Function Space SendProg Operation Keyboard and Speed Keyboard Operation Keyboard FunctionPLU DT/TM PRTFor VoidSelf Service Keyboard ZeroKEY Layout Procedure Before Operation Speed KEY SETInstallation Procedure Level Adjustment Removal and Replacement of Media Removal and Replacement of Media Power Outline of Operation1/4LB KEY 100g, kg KEY LB/kg KEY Registration modeXNOT Available Tmcc CMT-port communicarion Clerk LabelProgramming Procedures How to access to Programming MenuTitle and Contents of Programming Menu How to enter characters TEC StorePLU Data Edit MenuPLU Data Setting Set tare limitAuto Code Ingredient Message Nutrition Setting When entering PLU#, be careful of the following Daily Value Max digits Contents of Daily value Set the Daily Value TableMemory file is sorted when a memory full error occurs Deleting Nutrition DataMemory file sort PLU Verifying Label Menu Item No Verifies PLU data stored in the scaleAddress and Commercial Message Setting Combination Message Message construction Message display timeThank YOU Call Scrolling Flashing Curtaining Scrolling up Scrolling downThank YOU Thank YOU ANK YOU Call AGASpecial Information Grade LineDepartment Number Speed KEY SettingSetting Department/Vendor Number Vendor NumberPrint Format By pressing KeyLabel Format Number Table Format NoDATE/TIME Setting Menu Item NoCMT Operations Error code during PL-3 operation PL-3 OperationTransmission Item List Item #CMT Transmission Delay Time Table IN-LINE/LOCALLON System Price Address SL-9000N only Cancel Retry ContinueData Transmission Initial #0 #19, SL-9000N only① Weigh or Fix Price Format Default Bar Code FormatBAR Code Format ② By Count FormatFlag PLU # UPC # PC/D Price Weight PLU # UPC # PC/DAdditional 233 Title No Format Additional 221Additional 231 232 Additional 234 235 Additional 7,8 238 Additional 9,10 239Transferring Logo Data SL-9000N onlyVerify SL-9000=CMT Idiom Setting Error message during data transmissionVendor Setting Free Format Setting Key functionsEnter SP-INFO/NET WT Logo Frequent Shopper Print coordinate How to access Report menu Programmed Data Verification ReportsMenu Set the zone PLU #. Ex. PLU #100 ～108 R S Password SecuritySetting Password and Protect Menu R S X Z× ー × Calling Menu by Entering Password Operating Procedures How to access REG., M.DOWN, or Rewrap menuMenu REG., M.DOWN, or Rewrap Mode Weigh Weighing OperationFIX Price Operation for US Type only By Count Operation For Print Count Operation To check the remaining number, clear the PLU and press KeyExample B When operating in Fix or By Count mode Set the number of labels. Max labels Enter the PLU # Issuing Labels with NET Weight Statement for US Type only PLUSample label 14-10 TARE/SAVE Function Procedures Calling and Printing Grade Lines Calling and Printing Logos LogoMenu REG, M.DOWN, or Rewrap Mode WEIGH, FIX, or by Count Selecting Print ItemDate Change Batch Print Mode with 30 Items Run Assignment Unit Price Change and G.Line/LOGO Call Key is pressed to issue Label Issue Stop or CancelTotals Overflow error occurs when KeyVisual Commodity Library Dpt #Floating Vendor Price deletion SubtotalHow to access Read or Reset menu Total OperationPLU Total Report Hourly Total ReportGrand Total Report Ex. Report MenuVendor Total Report For Enter PLU TotalError Message Table Programming ModeLabel lssue Mode Report and Reset ModeLON System Mode Cleaning the Print Head Troubleshooting Before You Call for Service