Lifescan Basic Blood Glucose Monitoring System manual Button, Solution test

Page 66

MESSAGE

APPEARS WHEN

code--	The meter is turned on and you have not previously coded
	the meter. This is a reminder that you should verify that the
	code displayed on the meter matches the code on the test
	strip vial before testing. If it does not, reset by pressing the
	C button.

check code

The meter is turned on. This is a reminder that prior to testing you should verify that the code displayed on the meter matches the code on the test strip vial. If it does not, reset by pressing the C button.

insert	The meter is ready to perform a blood, check strip, or control
c o d e 1 0 (Example)	solution test.
strip

58

Image 66

Contents Basic Page Page Important The OneTouch Basic System kit contains Table of Contents Testing Your Blood Page Page Introduction Precautions Limitations Infection Control Getting Started OneTouch Basic Blood GlucoseComplete OneTouch Basic Blood Glucose Monitoring System OneTouch Basic Blood Glucose Meter Basic MeterTest Strip HOLDER. The test strip OneTouch Basic, Profile, OneTouch II Test Strips Test StripImportant Test Strip Information OneTouch Normal Control Solution To practice the test procedure,Before Testing Setting Meter CodeCode the OneTouch Basic Meter in these three easy steps Press the On/Off Button Match the Code NumbersChecking the System Code the MeterChecking with the Check Strip How to do a check strip test Page Example Checking with Control Solution Do a control solution test Control solution test tipsSpot with the tip of the vial Important Control Solution Test Information Spot facing up How to do a control solution testPress On/Off Button. Insert Test Strip Test strip in allApply Control Solution Control range You are ready to test your bloodControl solution results Meter malfunction Extremes in testing temperatures Testing Your Blood Abbreviated Test ProcedureDetailed Test Procedure TestGetting a Drop of Blood While the lancet is in the OneTouch Penlet Plus Sampler, twist off the proAdjust the puncture depth setting Cock the OneTouch Penlet Plus SamplerWash Your Hands Lance Your FingerRequired blood volume. Proceed with Remove the LancetYour blood glucose test Clockwise Always use caution when removing How to Test Your Blood Replace the vial Cap immediately Do not touch Test spot on Remove a testStrip from the vial Test strip. The testApply Blood Sample Drop Be sure that youTouch only the tip Blood to the testAccurate Results Seconds After the result is displayedResults will appear without time Date. See Special Messages Checking the Amount of Blood on the Test Strip If the following message Remove the testStrip from Back Comparing Meter and Laboratory Results Take your meter with you to the labComparing the results ExamplePage Using the Meter Memory Entering the Memory ModeRecalling Test Results Setting Meter Options Entering and Using Set-Up ModeIf you want to change an option setting, use the C button Clock option is set to and when it is set to Clock Time and DateSetting the Time Setting the Date Beep Prompts Or press the M button to move to the next optionLanguage Time Format Date FormatUnit of Measure Decimal SeparatorExiting the Set-Up Mode Itself off after two minutes of no activitySolving Problems Test Procedure MessagesSolution test Button108 mg/dL Mmol/L100 mg/dL 80 mg/dLHi mg/dL 58 mg/dLAlternating with 58 mg/dL Alternating withError Messages When this symbol is flashing, the batteries are too low BattryMeter was used in very bright light Test strip moved during Test New test strip Test strip was not insertedCorrectly New test strip 800 Error3 retest Not enough blood retest Your meter on, your meter’s If appearing when you turnWas turned on Test area may be dirtyRepeat the test with a Last test failed after the countdown started Strip vial to operate Message when the meterMeter requires a test Has not yet been codedKeep the test strip holder and test area clean see Taking Care Your MeterCleaning the Meter Doing a Daily CheckAppears on the display Remove the Test Strip Holder from the Meter Clean the Test Strip Holder Wash only the test strip holder withMay also be used. Do not apply full Careful not to scratch the test areaReplace the Test Strip Holder Replacing the Batteries Batteries should last aboutTo replace the batteries Remove the battery compartment DoorAgainst a hard surface References Remove the batteries and reinsert them as illustratedAlkaline batteries SpecificationsDimensions 4.3 2.6 Weight 4.1 ounces with batteries 15-35CGuarantee Warranty Day Money-Back GuaranteeThree-Year Warranty Page Index OneTouch Penlet Plus Adjustable Blood Page Page Page USA