Scan, Off, Again | Kenwood TS-440S instruction

3-6-3. Transferring data between memory channels

1.With the TS-440S in the memory mode, press the M.IN key and scroll to the channel that you want the data to be transferred to.

M CH

n, ILl ,-,cn '-', , ,. 1 , _,.U

2.Press the M .IN key. The frequency and mode of the memory channel that appeared before you pressed the M.IN key will duplicated in the new channel.

3-6-4. Entering/Transferring data in the split fre- quency channels

Separate transmit and receive frequencies may be en- tered into memory channels 90 through 99. The proce- dure is similar to that given for the other channels with the following exception:

1.The active VFO frequency and mode is stored in the receive memory, and the inactive VFO frequen- cy and mode is stored in the transmit memory, regardless of whether the SPLIT function is ON or

OFF.

2.The RIT offset is stored in the receive memory, and the XIT offset in the transmit memory.

3.When data is transferred from the general memory section into the split frequency memory section the transmit and receive frequencies will be the same.

4.Only the receive memory will be transferred into general memory during transfer operations from the split memory area.

3-6-5. Clearing a memory channel

Two methods may be used to clear a memory

channel:

1.M.IN switch

Transferring information from a vacant channel, i.e. one that has no stored information, thru the use of the M.IN switch, as described previously in section 3-6-1 is one

method of "clearing" a memory channel.

2.ENT switch

Data may also be erased by depressing the ENT key while depressing the CLEAR key.

3-6-6. Memory recall

Fixed channel type recall is possible when using the VFO/M key to recall memory channel information. The stored frequency cannot be changed, although the

RIT/XIT function is active.

1.Press the VFO/M key. The memory channel num- ber, mode, and stored frequency data will be dis- played. If a channel contains no data, only the channel number will be displayed.

2. Select the desired memory channel using the methods described under Memory Entry section.

3.To return to the VFO mode, press the VFO/M key

again.

,~ (; i: % t'~:J;;))!J'I

I:"-'-VF,lOVFOI7-'C,5.-,

, ,. , , -'U.

Notes:

1.RIT/XIT will be cancelled when the T5-4405 is switched from the VFO mode to the memory mode, but will be restored when the T5-4405 returns to the VFO mode.

2.When the T5-4405 is switched from the memory mode to the VFO mode, the VFO will be set to the

RIT/XIT variable specified when the data was programmed in to memory.

3-7. SCAN

3-7-1. Memory scan

Memory scan operates from memory channel 00 thru memory channel 99 at approximately 3-4 second in- tervals, or you may specify which memory groups you want to scan. Only these memory channels with data entered are scanned.

To initiate memory scan of all memory channels

1.Press the VFO/M key to select the memory mode.

2.Press the SCAN key. Scan will begin at memory channel 00, or the lowest numbered channel con- taining data.

3.You can stop scanning by pressing the CLEAR or

microphone PTT switch. Pressing the PTT switch will allow you to continue scanning from the point that you stopped, and pressing the CLEAR key will allow you to start scanning from the beginning.

4.To resume scan press the SCAN key again.

To initiate memory scan of specific memory channel groups

1.Press the VFO/M key to select the memory mode.

2.Press and hold the SCAN key.

3.You may specify which memory groups you want to scan by depressing the key that corresponds to the ten position of the memory channel group.

~..	Memory channels 00 thru 09,
	Memory channels 00 thru 09,
0=].	Memory	channels	10	thru	19,
~.	Memory	channels	20	thru	29
~	Memory	channels	90 thru		99
					17