In example 1 we want to scan only Group 2, so we would press the 2 key. In example 2 we want to scan Group 1 and Group 2, so we would press the 1 key
and then the 2 key.
Example | 1 | Example 2 |
|
| |
Group 2 | GH1U- | Group 1 | Group 2 . | ||
~ | ~~ |
| lJM"" | ||
I.;M"\1 |
| ||||
| |||||
t
4. You can stop scanning, or resume scan using the
same methods described above for the entire
memory scan.
3-7-2. Program scan
Two programmable scan ranges are provided on the
2)utilizes memory channels 08 and 09 to specify the upper and lower scan limits.
To initiate PG.S
1.Press the VFO/M key to select VFO operation.
Press and hold the SCAN key
3.To initiate PG.S 1 press the 6 key, and then release both the 6 and the SCAN keys. Scan will begin on
the frequency programmed in memory channel number 6 and proceed in 10Hz steps to the upper limit stored in memory channel 7, then return to channel 6 and begin again.
,-PGS-1---,
CH6CH7
1401000 14.100.00
CWI'~I
.;
L,
4.To initiate PG.S 2 press the 8 key, and then release both the 8 and the SCAN key. Scan will proceed in the limits specified in memory channels 8 and 9, just as for PG.S 1.
CH8CH9
14.200.00 14.320.00
use. .~
5.If you want to scan both ranges PG.S 1 and PG.S 2, press the 6and then the 8 key while holding the SCAN key down, and then release the SCAN key. Scan will proceed thru the limits in memory chan- nels 6 and 7, thru the limits in memory channels 8 and 9, and then return to begin the process again.
| r- | ||
CH6 | CH7 | CH8 | CH9 |
CW + | u~~ |
| |
l |
|
| |
|
|
| |
6.To stop scanning press the Pi] switch, or the CLEAR key. Pressing the SCAN key allows scan to resume from the point you stopped.
.2418
Note:
,'j
The
low whatever you have entered the next time you press the SCAN key.
Example 1: Memory mode
Previously programmed memory scan data was to scan channels
40-49.
To scan this same range again simply press the SCAN key.
Example 2: VFO mode
Previously entered program scan data was to scan both PG.S1 and PG.S2.
To initiate program scan over these two ranges again simply press the SCAN key.
The
information. This saves a lot of key strokes if you al- ways scan the same ranges, etc.
3-7-3. Scan speed
Two scan speeds are available with the
To change the speed press the 5CAN key after you have initiated scan. You will be able to toggle between fast and slow each time you press the key.
Note:
The scan step size depends upon the mode that has been selected for S5B, CW and AF5K the step size is 10Hz, for FM and AM the step size is 100 Hz.
3-7-4. Memorychannellockout
This transceiver has a memory channel lockout func- tion which allows you to temporarily skip unwanted memory channels during memory scan.
1.Press the VFO/M key to enter the memory mode.
2.Select the memory channel that you want to skip using the numeric keypad, the TUNING knob, or the UP/DOWN microphone or BAND switches.
3.Press the CLEAR switch.
A decimal point will appear in the M.CH display to indicate that the channel will be skipped.
,_,. u
5.To cancel the lockout, select the desired channel and then press the CLEAR switch. The decimal point will go out indicating that the channel will again be scanned.