Invacare EX2 warranty Installing Impact Guards/Calf Strap, Replacing Heel Loop

Page 22

SECTION 4—FRONT RIGGINGS

Installing Impact Guards/Calf Strap

NOTE: For this procedure, refer to FIGURE 4.6.

1.Remove impact guard/calf strap from packaged container if not already secured to the footrest.

2.Secure one impact guard to the each footrest.

NOTE: Ensure the upper portion of the impact guard is between the two horizontal supports of the footrest.

3.Secure one side of the calf strap around each footrest (with the impact guards attached, if present).

 

Horizontal

 

Support

Calf Strap

Notch

 

Footrest

Upper Portion of

Impact GuardImpact

Guard

Horizontal Support

FIGURE 4.6 Installing Impact Guards/Calf Strap

Replacing Heel Loop

NOTE: For this procedure, refer to FIGURE 4.7 on page 23.

1.Pull the cam lock lever up to unlocked position.

2.Perform one of the following as shown in Detail ʺAʺ.

Footplates with Spring Buttons:

i.Push in the release buttons and remove the footplate assembly from the front rigging support.

Bolt‐In‐Place Footplates:

i.Using a screw driver to hold the threaded rivet in position, remove the button head screw from the threaded rivet.

ii.Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support.

3.Remove the mounting screw, spacer and locknut that secure the heel loop to the footplate.

4.Remove existing heel loop from slide tube.

5.Install new heel loop onto slide tube.

6.Install the mounting screw, spacer and locknut to secure the heel loop to the footplate. Tighten until the spacer is secure.

7.Insert the lower footrest assembly into the upper footrest assembly to desired height.

8.Perform one of the following as shown in Detail ʺAʺ:

Footplates With Spring Buttons:

i.Ensure that the release buttons fully protrude from holes on both sides of the upper footrest support.

Bolt‐In‐Place Footplates:

i.From the outside of the swingaway front rigging, insert the threaded rivet through both the front rigging support and the footplate assembly.

ii.From the inside of the swingaway front rigging, insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet.

iii.Using a screwdriver to hold the threaded rivet in position, securely tighten the button head screw. Torque to 32 in‐lbs.

9.Rotate cam lock lever down to locked position.

Tracer® EX2

22

Part No. 1110546

Image 22
Contents Tracer EX2 Accessories Warning Special Notes Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsLabel Location Important NoticeTypical Product Parameters Anti-Tippers General GuidelinesStability All Models Operating InformationImmediately Weight Training/Weight Limitation Stability and Balance SAFETY/HANDLING of WheelchairsSafety/Handling of Wheelchairs Coping With Everyday ObstaclesReaching and Leaning Backwards Reaching, Leaning and Bending ForwardDo not tip the wheelchair without assistance Method 1 Wheelchair With Step Tubes Method 1 Wheelchair With Step TubesEscalators StairwaysTransferring To and From Other Seats Unfolding and Folding WheelchairDo not allow upholstery to hang between the cross braces Folding WheelchairFolding Hammock or Sling Seat Models Safety INSPECTION/TROUBLESHOOTING Safety Inspection ChecklistMaintenance Inspect/Adjust WeeklySafety INSPECTION/TROUBLESHOOTING Troubleshooting Right/Left Wheels Performance Flutter Rattles ChairAdjusting Footplate Height Installing/Removing Front RiggingsFront Riggings Bolt-In-Place Spring ButtonRaising/Lowering Elevating Legrest Assembly Fixed FrameInstalling Impact Guards/Calf Strap Replacing Heel LoopReplacing Heel Loop Adjusting Armrest Height ArmsRemoving/Installing Armrests Installing ArmrestReplacing Back Upholstery Seat and BackReplacing Seat Upholstery Adjusting the Seat Width Swingaway Front RiggingsDetail B Crossbrace Removing Lower Mounting Hardware Removing/Installing Rear Wheels Rear WheelsReplacing/Repairing Rear Wheel Tire Replacing Rear Wheel HandrimFront Casters Adjusting ForksReplacing Front Casters Replacing/Repairing Front Caster Tire Replacing Front CastersInstalling/Adjusting Anti-tippers ANTI-TIPPERS/WHEEL LocksUsing/Adjusting Patient Operated Wheel Locks Adjusting the Anti-TippersUsing Patient Operated Wheel Locks Seat to Floor Changing Seat-to-Floor HeightInstalling Amputee Bracket OptionsInstalling Crutch and Cane Carrier Installing the Seat Positioning StrapLimited Warranty
Related manuals
Manual 30 pages 6.48 Kb